143700 - Overview

Models starting with 143700

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Heat Resistant Adhesive – Part Number: W10841140
$29.65
In Stock
Heat Resistant Adhesive
★★★★★
★★★★★
(1)
Part #W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.
Ceramic Fuse - 20 amp – Part Number: WPM0805101
$16.37
In Stock
Ceramic Fuse - 20 amp
★★★★★
★★★★★
(1)
Part #WPM0805101
This ceramic microwave fuse is just over an inch long. It is white in the center, while each end is made of metal. This is a twenty amp fuse.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Refrigerator Screw – Part Number: WP98165
$10.95
In Stock
Refrigerator Screw
Part #WP98165
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Range Hex Nut – Part Number: WP488130
$12.05
Special Order
Range Hex Nut
Part #WP488130
Part may differ in appearance, but functions same as original.
2-Speed Drive Motor with Jumper Wire – Part Number: 12002353
No Longer Available
2-Speed Drive Motor with Jumper Wire
Part #12002353
This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries 8.0 amps. It's a good idea to change your washer's belts at the same time as you replace this motor, as they may have become worn as well.
Refrigerator Screw – Part Number: WP489464
$15.39
In Stock
Refrigerator Screw
Part #WP489464
Sold individually.
Washer – Part Number: 650691
No Longer Available
Washer
Part #650691
Brushing, Governor Lever – Part Number: 31966
No Longer Available
Oil Seal – Part Number: 31950
No Longer Available
Oil Seal
Part #31950
O Ring – Part Number: 33487
No Longer Available
O Ring
Part #33487
Breather – Part Number: 33489
No Longer Available
Breather
Part #33489

Exact Part matches for your search term

CONTROL MODULE – Part Number: 143700
No Longer Available
CONTROL MODULE
This part number matches the current model number 143700
Part #143700
CONTROL UNIT – Part Number: 00143700
No Longer Available
CONTROL UNIT
This part number matches the current model number 143700
Part #00143700
Thumb Screw – Part Number: 143700
No Longer Available
Thumb Screw
This part number matches the current model number 143700
Part #143700

Common Symptoms of models starting with 143700

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
microwave oven blew fuse
27 of 43 people found this instruction helpful.
  • tad from tamarack, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
Was this helpful?
Thank you for voting!
Motor Froze
22 of 28 people found this instruction helpful.
  • Matt from Oxford, GA
  • A Bit Difficult
  • 1- 2 hours
  • Nutdriver, Pliers, Screw drivers
Make sure to release the springs and pulleys before you try to tackle the bolts that hold the motor base to the bottom of the washer. Mine were a bit rusty and took some force to break loose. Also it's a good idea to take pictures of how everything sits before you disassemble as the pictures in the repair kit are not very clear. Oth er than that it was pretty straight forward. Wiring was a breeze. . . . Good luck
Was this helpful?
Thank you for voting!
the motor burnt out
17 of 24 people found this instruction helpful.
  • walter from watertown, WI
  • Really Easy
  • 1- 2 hours
  • Socket set
took washer into the garage, removed front cover & disconnected the wiring. Then i removed the motor assembly. Piece of cake to finish job.
Was this helpful?
Thank you for voting!