143300 - Overview

Models starting with 143300

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Heat Resistant Adhesive – Part Number: W10841140
$29.65
In Stock
Heat Resistant Adhesive
★★★★★
★★★★★
(1)
Part #W10841140
This is a heat-resistant adhesive for your appliance. The heat resistance allows you to stick parts such as grate feet, gaskets, and felt seals in hot areas, such as a cooktop, without compromising the integrity of the adhesive. It is white in color, and the tube is approximately 7.5 inches long.
Ceramic Fuse - 20 amp – Part Number: WPM0805101
$16.37
In Stock
Ceramic Fuse - 20 amp
★★★★★
★★★★★
(1)
Part #WPM0805101
This ceramic microwave fuse is just over an inch long. It is white in the center, while each end is made of metal. This is a twenty amp fuse.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Range Hex Nut – Part Number: WP488130
$12.05
Special Order
Range Hex Nut
Part #WP488130
Part may differ in appearance, but functions same as original.
Bowl-fuel Filter – Part Number: 298683
$24.95
Special Order
Bowl-fuel Filter
Part #298683
Kit-carb Overhaul – Part Number: 394693
$55.95
Special Order
Kit-carb Overhaul
Part #394693
An engine that surges, stalls, or will not stay running can have dirt or worn seals inside its float carburetor. This rebuild kit contains gaskets and small service pieces for restoring the carburetor rather than replacing the complete unit. Inspect the fuel supply and ignition system first, then confirm the engine identification and carburetor design. Work only on a cool engine in a ventilated area. Drain all fuel, disconnect the spark plug wire, and keep sparks and cigarettes away. Photograph the linkages, clean passages without enlarging them, install each gasket in the correct order, and check carefully for leaks before starting the engine.
Gasket-intake – Part Number: 27828S
$8.95
Special Order
Gasket-intake
Part #27828S
It is a manufacturer supplied replacement part that is designed for use with Briggs and Stratton engines. This carburetor intake gasket which provides an air tight seal for the breather assembly. Over time gaskets tend to deteriorate and crack eventually needing a replacement. It is made from durable composite material and it is sold individually.
Kit-idle Mixture – Part Number: 292681
$20.95
Special Order
Kit-idle Mixture
Part #292681
This is an authentic replacement part manufactured for use with Briggs & Stratton small engines. The idle mixture kit is used to adjust the amount of fuel that is sent to the engine's intake while the engine is idling. This idle mixture kit is available as an individual replacement part.
Pulley-starter – Part Number: 295871
$25.95
Special Order
Pulley-starter
Part #295871
Difficulty pulling the starter rope or a cord that stays extended can result from a damaged recoil pulley. This wheel guides and stores the rope while helping turn the engine during starting. Similar symptoms can come from a frayed rope, seized engine, bent starter housing, broken pawls, or weak return spring, so check those items first. Match the replacement to the full engine model, type, code, and equipment model. Work on a cool engine with the spark plug lead removed. Release spring tension slowly and keep your face and hands clear of the starter housing. Route the rope correctly, confirm smooth return, and reinstall every guard before starting the engine.
Gasket-crkcse/009 – Part Number: 27877
$18.95
Special Order
Gasket-crkcse/009
Part #27877
Engine Breather Gasket – Part Number: 27803S
$7.95
Special Order
Engine Breather Gasket
Part #27803S
This is a high-quality manufacturer-sourced part which is made for use with Briggs and Stratton engines commonly installed on lawn and garden equipment. It helps to distribute the pressure evenly and provide a tight seal for the breather. Over time it may become brittle and begin to crack eventually requiring a replacement. For the proper application please refer to the appropriate diagrams of your model. This high-quality part is made of durable composite material and is sold individually. You will need a screwdriver and a wrench set to remove and reattach the breather.
Seal-oil – Part Number: 294606S
$17.95
Special Order
Seal-oil
Part #294606S
This is an original replacement part manufactured for use with outdoor power equipment. The oil seal is used with a variety of different models of equipment and is commonly used to form a seal where camshaft or driveshaft exit the crankcase. This oil seal is sold as an individual replacement part, please see model diagram for associative parts.

Exact Part matches for your search term

SHELF-DEEP, 48 IN. – Part Number: 143300
No Longer Available
SHELF-DEEP, 48 IN.
This part number matches the current model number 143300
Part #143300
SHELF – Part Number: 00143300
$241.82
Special Order
SHELF
This part number matches the current model number 143300
Part #00143300

Common Symptoms of models starting with 143300

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
microwave oven blew fuse
27 of 43 people found this instruction helpful.
  • tad from tamarack, MN
  • Really Easy
  • Less than 15 mins
  • Pliers, Screw drivers
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With th e help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.
Was this helpful?
Thank you for voting!
microve stopped working
15 of 30 people found this instruction helpful.
  • Denice from Montgomery, AL
  • Really Easy
  • 15 - 30 mins
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise
Was this helpful?
Thank you for voting!
Died while heating lasagna
9 of 17 people found this instruction helpful.
  • connie from madison, NC
  • Really Easy
  • Less than 15 mins
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.
Was this helpful?
Thank you for voting!