1426X2A Roper Range - Overview

Diagrams for 1426X2A

See every part. Know exactly what you need.

Parts for the 1426X2A

$69.25

Surface Burner Element Switch, Large Burner

★★★★★

(48)

Part #WP3149400

This control switch controls the stove top 8" surface burner. 8.9- 11.0 amp. This surface burner element switch is for an 8-inch surface burner on an oven, stove, or range. The element switch controls the heat of the surface burner. Disconnect power to your range before completing this repair because you will be working closely with elec...Read more

Read less

$33.28

Lid Switch

★★★★★

(7)

Part #W10820036

Keep your washer or dryer running safely with this easy-to-install lid or door switch kit. It stops the machine from working when the door is open, helping prevent spills and accidents. Compatible with many models, this small but important part fits neatly inside your appliance and comes with everything you need for installation. Just unp...Read more

Read less

$70.12

Blower Belt

★★★★★

(3)

Part #WP691371

If your dryer isn’t drying clothes like it used to or making strange noises, this blower belt might be the fix. It connects the motor to the blower wheel, helping move air through the drum so clothes dry faster. Made to fit select Whirlpool models, it’s tough and reliable. Just unplug your dryer before installing and check your model number to make sure it’s the right part!

$10.95

Range Hex Nut

Part #WP112432

10-32 hex - Sold Individually - Appliance originally takes 3 of this item.

Switch-Gas Valve

Part #331174

SERVICE MOTOR-60 CYCLE (PRODUCTION MOTORS 296086, 295976 OR 295977)

Part #299761

Aeration Pan (4 Req)

Part #330427

xSpring-Broiler Drawer

Part #327481

24062A, 24262A Models

Part #336546

Left

Part #327216

24060A, 24260A Models

Part #330343

Main Bottom

Part #327053

Common Symptoms of the 1426X2A

How this model fails, and the parts that fix it.

Element will not heat

Oven not heating evenly

Fixed by
these parts

Show All

Videos related to models starting with 1426X2A

Watch our pros, then fix it yourself.

Replacing the Surface Burner Element Switch, Large Burner

Replacing the Lid Switch

Repair Tips From Fixers Like You

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

the element did not turn compleatly off, the on light stayed on.

89 of 109 people found this instruction helpful.

chaz from fairplay, CO
Easy
15 - 30 mins
Screw drivers

removed the screws holding the back metal panel, this exposed the wires to the switch. tested the wires to find that they were live when the switch was in the off position. ordered a new switch. UNPLUGED THE STOVE. removed the knob on the front of the stove. this exposed 2 screws, removed screws and the switch came away from the stove. re ... Read more

Read less

Was this helpful?

Burner would go high without warning

60 of 63 people found this instruction helpful.

John from Clinton, CT
Easy
15 - 30 mins
Pliers, Screw drivers

We felt the only possible problem could be the switch assembly. I removed the switch panel, removed the wires from the old switch, one at a time, removed the old switch assembly and installed the new switch assembly. The extended stem did have to be snapped off (per your instructions) and that too was a very simple task.

Was this helpful?

Left front burner would not adjust heat downward

35 of 40 people found this instruction helpful.

ALTON from ROUND ROCK, TX
Easy
15 - 30 mins
Screw drivers

Pull unit away from wall.
Unplug power
remove topmost four screws from rear metal cover
Pull knob off switch shaft.
Remove two screws holding switch to panel.
Break off shaft of new switch to correct length.
Remove each wire from old switch and attach to Corresponding lug on new switch.
Reattach the new ... Read more

Read less

Was this helpful?