My Orders
126T02-0395-B1 Briggs and Stratton Engine - Overview
Diagrams for 126T02-0395-B1
See every part. Know exactly what you need.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$13.95
Special Order
Seal-oil
Part #399781S
This is an authentic replacement part manufactured for use with small engines. Seals can deteriorate overtime, and it is recommended to replace worn seals when servicing an engine. This seal is the lower seal in the engine's sump, the seal is sold individually.
$7.95
Special Order
Bolt
Part #691119
$88.95
Special Order
Engine Recoil Starter Assembly
Part #497680
This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a durable plastic shroud/housing, starter pulley, recoil spring, pull rope with grip, and the necessary hardware for installation. It functio...Read morens as the primary mechanism for manually cranking and starting the engine. To complete the replacement, you’ll need a wrench. Simply remove the four screws and nuts securing the old starter assembly, then install the new one using the included hardware. This item is sold as a complete individual assembly.
Read less
$11.95
Special Order
Filter-a/c Foam
Part #493537S
Genuine Manufacturer Sourced replacement part used on a variety of Briggs and Stratton Engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is a Foam Pre-Cleaner which is Sold Individually. Please note a Paper Filter and a Cover are both Sold Separately.
$30.95
Special Order
Shaft-Throttle
Part #493267
$6.95
Special Order
Screw
Part #691142
$11.95
In Stock
Kit-needle/seat
Part #398188
Genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. This item includes the seat. The needle valve opens and closes to control the flow of fuel into the carburetor. Make sure to disconnect the spark plug wire and drain all gasoline from the carburetor and fuel tank before starting a repair.
$15.95
Special Order
Deflector-muffler
Part #393760
This is a genuine Briggs & Stratton and Toro replacement part for use in engines, lawn mowers, and lawn tractors. The muffler deflector is made out of metal. A wrench may be needed during the replacement of this item. It will need to be replaced if it breaks. This item is sold individually.
$27.95
Special Order
Deflector-Muffler
Part #396548
$5.95
In Stock
Seal-o Ring
Part #270344S
This authentic OEM replacement part fits a variety of Toro and Briggs & Stratton engines. An O ring is used to retain pressure between rigid parts. Its flexible material allows it to create a tight seal. Many different sizes of O ring are used in these engines; consult manual to be sure of correct placement. Sold individually.
$5.95
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
$6.95
Special Order
Washer-sealing
Part #271716
This authentic OEM sealing washer is designed for your lawn equipment to create a tight seal within the carburetor body, preventing fuel or air leaks. If you notice any signs of leaks, such as dripping fuel or hissing sounds, it may indicate a faulty or worn-out sealing washer. Additionally, you might be experiencing engine performance is...Read moresues like rough idling or difficulty starting. To replace the sealing washer, ensure that the machine is off and that the engine has cooled down. Remove the air breather cover and the filter itself, following the instructions provided in your user manual to access the carburetor. Depending on your specific equipment model, you may need to detach the springs from the carburetor choke mechanism, disconnect the fuel line and fuel tank, remove the choke lever, and detach the air breather base. Once you have located the carburetor, carefully unthread the main jet from the bottom of the carburetor bowl. Finally, slide off the old sealing washer, ensuring you take note of its positioning for accurate replacement. Please note that this sealing washer is sold individually.
Read less
Common Symptoms of the 126T02-0395-B1
How this model fails, and the parts that fix it.
Will Not Start
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
Engine will not idle
Fixed by
these parts
these parts
Show All
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Mower was submerged in Hurricane Matthew
25 of 51 people
found this instruction helpful.
Total disassemble, clean out water and any rust. hone cylinder, wire brush where needed,reassemble with new rings,gaskets and seals and lucas oil product. Started on second pull. Mowed lawn. If you have never done this sort of work before, probably should not attempt.
Other Parts Used:
Was this helpful?
Thank you for voting!
Smelled Gas Leaks
8 of 11 people
found this instruction helpful.
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together ... Read more with all the necessary clamps.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together ... Read more with all the necessary clamps.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!