122K00 (0006-3113) Briggs and Stratton Engine - Overview
Sections of the 122K00
[Viewing 5 of 5]Keep searches simple, eg. "belt" or "pump".
Seal-o Ring
PartSelect #: PS8936675
Manufacturer #: 270344S
This authentic OEM replacement part fits a variety of Toro and Briggs & Stratton engines. An O ring is used to retain pressure between rigid parts. Its flexible material allows it to create a tight se...
$5.95
In Stock
Rep Man-1 Cyl L-hd
PartSelect #: PS8937789
Manufacturer #: 270962
This is a genuine item that is supplied directly from the original equipment manufacturer for Briggs and Stratton engines commonly installed on lawn and garden equipment. The repair manual contains ea...
$51.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Washer-sealing
PartSelect #: PS8940580
Manufacturer #: 271716
This authentic OEM sealing washer is designed for your lawn equipment to create a tight seal within the carburetor body, preventing fuel or air leaks. If you notice any signs of leaks, such as drippin...
$6.95
In Stock
Key-woodruff
PartSelect #: PS9063568
Manufacturer #: 690979
This timing key is an OEM direct from Briggs & Stratton. The metal component is compatible with many small engines, and is sold individually. The key secures the shaft in the crankshaft. A wrench is o...
$5.95
Special Order
Seal-o Ring
PartSelect #: PS9063625
Manufacturer #: 691031
This authentic item is supplied directly from the original equipment manufacturer for use with engines, outboard motors, portable generators, snowthrowers, and lawn mowers made by Briggs & Stratton an...
$9.95
Special Order
Valve-throttle
PartSelect #: PS9076856
Manufacturer #: 696564
Used With Plastic Throttle Shaft
$15.95
Special Order
Common Symptoms of the 122K00
[Viewing 3 of 3]Will Not Start
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
Engine will not idle
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
starter rewind cord broke
I found the model number of the Briggs & Stratton engine on the inside of the engine housing. Ordered a new starter-rewind unit, as the old cord broke and the thing was well worn. The instructions were clear enough, but to get the old starter off I had to drill out four rivets, which just spin around when you try. I used a hacksaw, chisel, pliers, whatever worked on each rivet; this took a while. When they were finally removed, the new starter pull unit was relatively easy to install with the small nuts and bolts provided. On the Yard Machines log splitter, putting back the engine housing is quite tricky; you have to jostle the thing into place, get the pull handle above the cover and line up the bolt holes.
Parts Used:
-
Seikai from MARICOPA, CA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers, Socket set, Wrench (Adjustable), Wrench set
15 of 21 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Smelled Gas Leaks
Inspected/removed fuel lines and found signs of leak. Removed and inspected carburetor and found that seals and gaskets were toast. Replaced said seals with ones from the kit that fit and replaced fuel lines.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Would be nice to have a fuel line kit with the big fuel line (tank to carb) and the little one (carb to engine) together with all the necessary clamps.
Parts Used:
-
Jonathan from LIBERTY TWP, OH
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Wouldn’t start.
I installed a new solenoid starter. Took me a total of 20 minutes. Started right up.
Parts Used:
-
Bruce from CARNATION, WA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
18 of 44 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!