110C67042801 Kenmore Dryer - Instructions

ordered new lint screen, removed old screen, inserted new screen.

Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 months! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!

Had to remove the back of unit to access the area of subject part by removeing 12 to 14 screws also the gas line had to be removed. Two screws held the part in place. Unit now runs normal.Saved alot on repair costs!!!!!

Removed old filter and put in new one.

Replaced

I tried to follow directions followed by others on this site after diagnosing the problem via suggestions provided by users. I have a Whirlpool Duet dryer from 2002. We've had problems since moving about 3 years ago. I removed the front panel (lower) by unscrewing the two bottom screws (1/4" sheet metal screws). Then I took out the lint screen and the metal tube/contraption immediately beneath to get access to the area where thermistor is located. See the drawing/chart to help you locate this. It's really easier than it seems. Make sure you have the chart/drawing for your model - it makes difference! The thermistor came out pretty easily with a nutdriver that has a swivel offset shaft. Ask your hardware store tool dept. about that one. Put everything back in reverse order of course and test either with/without the front panel re-attached. In my case it fixed at least part of the problem. I was able to get clothes almost dry with most settings but I have yet to install the moisture sensor to see if that helps in addition to the internal-bias thermistor. I am the kind of person that does one thing at a time so at least I now know the thermistor was bad. Good luck and hang in there with your own repair. It's a lot cheaper even if it takes you longer to do than a pro.

Took the old filter out and inserted the new one- works great!!

Pulled out the old and slid in the new filter

Received in two days, open box, installed part. Pretty easy, fast service. I'm a repeat customer and will use these guys in the future.

Inside the dryer tub, remove the filter housing by removing two phillips head screws. Unplug the sensor wires, note when replacing wires, black wire goes on upper sensor.
Separate filter grill from housing. Using the pliers, compress the tabs on the sensor plugs and push it thru the grill. The small blade screwdriver may come in handy here to pry up on sensor to assist in pulling the plug end through the grill. Replace the sensors by hooking short end into grill and pushing the long end through the grill. When replacing the housing to the dryer, the most difficult thing is getting the screwdriver onto the recessed screws. Be sure to put the tab on top of the housing under the dryer frame when rotating the assembly into place.

Unscrewed the bottom panelof the dryer and located the thermistor through the schematic for my machine. Removed the old one and put the new one in the same way. No more E1 problems and all cycles now complete themselves.

i could not find this part anywhere locally,so i found this web site which had this part.i ordered this part and am very glad i did.i received it in 2 days.thank you very much.if you need anything check this place first,you will be very satisfied.

I was not able to find a video (or other specific instructions) that showed how to access the insides of this particular machine, but eventually figured out that all it takes is popping 2 clips, one on either side of the door by wedging a flathead screwdriver in the space between the top of the machine and the bottom piece that surrounds the door opening. The top then pivots up and can be moved back beyond vertical so that it hold itself in position.

After removing the dryer door, getting to the drum itself was not too difficult and only involves removing half a dozen small bolts. I was able to move the pieces off to the side without disconnecting any of the wiring. Without looking at the parts diagram I can't name any of the pieces involved, but there were only a couple. The drum can then be lifted right off its rollers.

The replacement felt for this dryer has to be fastened with adhesive, and I would recommend running the bead of glue around half of the drum, setting the new felt in place, letting it sit for a few minutes to let the glue set up, then repeating for the other half. I tried installing the entire piece of felt at once, but after getting about 3/4 of it on, pulling the remaining unattached felt taut to fit around the drum ended up removing the first part of the felt because the glue did not have time to set up. If you've ever changed a bicycle tire, you'll know about reaching that point where the tire doesn't seem big enough to fit around the rim, but it just needs to be muscled into place. Same idea here, but trying to muscle the felt over fresh glue while the just installed part comes loose is frustrating and in my case almost resulted in ruining the entire new felt strip. Once the felt is anchored it's easy to pull taut over the remaining part of the drum.

I noticed that drying time was increasing. I took the covers off the dryer to reach the fan and discovered that the squirrel cage fan buckets were packed with lint, and therefore not moving the air as intended. This was because the original lint filter caught most of the lint, but some bypassed the lint filter and then built up in the fan wheel buckets. The lint bypassed the lint filter because there was no felt gasket on the original filter as far as I can tell. I replaced the lint filter...and the replacement filter includes the felt seal (and fits tightly in the slide). The original lint filter has a provision for the felt seal, but I don't recall ever seeing it (and I did not see remnants of it in the fan or duct). As a matter of fact, I was always suspicious of how loosely the lint filter fit in the slide. The felt seal is not available as a replacement part from Maytag. That said, felt material 3/16"x1/2"x10ft is available from McMaster-Carr...and it fits nicely in the original lint filter.

The part wasn’t for my machine. Unfortunaly I was not able to repair it. I was sent stripe of foam with an adhesive strip on the back. I needed a felt strip.