11089675700 Kenmore Washer Dryer Combo - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Thermal Fuse – Part Number: WP3392519
$25.19
In Stock
Dryer Thermal Fuse
★★★★★
★★★★★
(149)
Part #WP3392519
This part is a one-time use thermal fuse which attaches to the blower wheel housing of your clothes dryer. It cannot be re-set and must be replaced when there is no longer continuity between the pins. Terminal size is 3/16".
Agitator Directional Cogs – Part Number: 80040
$6.55
In Stock
Agitator Directional Cogs
★★★★★
★★★★★
(200)
Part #80040
These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.
Door Catch Kit – Part Number: 279570
$10.58
In Stock
Door Catch Kit
★★★★★
★★★★★
(87)
Part #279570
This kit contains two door strikes, and three door catches to service dryer doors that have one or two catches.
Rear Drum Support Roller Kit – Part Number: 349241T
$29.23
In Stock
Rear Drum Support Roller Kit
★★★★★
★★★★★
(63)
Part #349241T
This dryer drum roller kit is designed to restore smooth and quiet operation in a wide range of dryer models. It includes two drum rollers, four tri-rings, and one to two retaining washers, providing all necessary components for a complete replacement. The rollers support the drum as it rotates, and worn or damaged rollers can cause excessive noise, poor tumbling performance, or even leave marks on clothing. Replacing these components can resolve issues such as rumbling, squealing, or grinding sounds during operation. Compatible with many units from Whirlpool, Kenmore, Sears, and other brands, this kit offers a reliable solution for maintaining optimal dryer performance.
Water Inlet Valve with Mounting Bracket – Part Number: 285805
$46.79
In Stock
Water Inlet Valve with Mounting Bracket
★★★★★
★★★★★
(41)
Part #285805
The valve body of this part could be blue or green in color. There are two ports for water to enter, and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Washer Tub Spring – Part Number: WPW10250667
$12.95
In Stock
Washer Tub Spring
★★★★★
★★★★★
(23)
Part #WPW10250667
This part is used to balance the tub during spin cycle. Sold individually.
Drive Motor with Pulley – Part Number: 279827
$151.26
In Stock
Drive Motor with Pulley
★★★★★
★★★★★
(29)
Part #279827
If your dryer drum isn’t spinning, the motor might be the issue. This replacement motor works with many Whirlpool-brand dryers made before 1996 and comes with the pulley already attached. It powers the drum by turning the belt, helping your clothes dry properly. Just make sure to unplug the dryer before starting the repair. Once installed, your dryer should be back to working like new.
Dryer Lint Filter and Cover – Part Number: W10828351
$77.53
In Stock
Dryer Lint Filter and Cover
★★★★★
★★★★★
(24)
Part #W10828351
This dryer lint filter and screen assembly is a genuine replacement part designed to trap lint and fibers during the drying cycle, helping to maintain airflow and prevent blockages in the vent system. Its kidney-shaped screen is constructed from durable steel and ABS plastic, housed within a cover that features four metal clips for secure installation. By capturing debris, it supports efficient drying times and reduces the risk of overheating or fire hazards. Compatible with various Whirlpool, Kenmore, and associated brand dryers, this OEM part replaces several previous versions and ensures a precise fit. Regular inspection and replacement of the lint filter are recommended to maintain optimal dryer performance.
Dryer Idler Pulley Assembly – Part Number: WP691366
$24.19
In Stock
Dryer Idler Pulley Assembly
★★★★★
★★★★★
(2)
Part #WP691366
The idler pulley wheel provides the tension for a multi-ribbed belt and helps the belt to rotate the drum. The drum will not spin if the idler pulley fails to put the correct amount of tension on the belt. The wheel is white in color and is made of plastic. If the drum will not tumble, is noisy, or will not start, you may need to replace this part. This idler pulley is a genuine OEM part. Please remember to disconnect the power to your dryer before you start your repair.
Washer Inner Cap Seal – Part Number: WPW10072840
$15.41
In Stock
Washer Inner Cap Seal
★★★★★
★★★★★
(2)
Part #WPW10072840
Also known as an O-Ring. This black o-ring seal is three inches in diameter.
Centerpost Gasket – Part Number: W10814296
$12.01
In Stock
Centerpost Gasket
★★★★★
★★★★★
(6)
Part #W10814296
This main outer tub seal is a critical component that prevents water from leaking at the bottom of the tub during operation. Measuring approximately 2 inches in diameter, it is constructed from durable black plastic for long-lasting performance. Proper installation requires disconnecting power, drain hose, and inlet hose, followed by removing the outer cabinet and the entire tub assembly. Inspect the seal for cracks or wear during maintenance to avoid leaks and ensure optimal washer performance.

Common Symptoms of the 11089675700

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer was working, but no heat.
3070 of 3494 people found this instruction helpful.
  • ANTHONY from CHESHIRE, CT
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
First I unplugged the dryer, then removed the back panel, this exposed most all of the wiring and I could see the heater coils.
Not knowing what the problem was I started looking at the coils and could not see any broken parts.
So then checked the thermal fuse for continuity I removed the two wires from it with a small pair of needle nose pliers, it was held in place by two screws, once they were removed the fuse came out easily, I checked continuity with a volt meter placing the meter on X1 Ohms and could not get a reading.
I replaced with a new one and put it all back together the way I took it apart.
Then I plugged it in and it worked first time, I now have warm dry clothes.
Was this helpful?
Thank you for voting!
washer wouldn't agitate
956 of 1058 people found this instruction helpful.
  • mike from Kent, WA
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the a gitator housing using the slots on the side for a guide. (You may want to remove the entire agitator and assemble everything upside down, then flip it all back over to mount, so the cogs don't fall out).
Tighten the bolt, snap the cap back in place on top of the agitator and your'e done. Easy repair.
Was this helpful?
Thank you for voting!
No heat but would run otherwise
928 of 1024 people found this instruction helpful.
  • Dana from Grassvally, CA
  • A Bit Difficult
  • More than 2 hours
  • Screw drivers
Cleaning the lint out of the whole machine took quite a bit of time--it was everywhere. Underneath the lint trap was a collection that ultimately ruined the thermal fuse where it restricted the air flow considerably.

Ascertaining the problem was the most time consuming part.

The actual repair was quite simple and did n't take but 15-20 minutes.
Was this helpful?
Thank you for voting!