11071633610 Kenmore Dryer - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Idler Pulley – Part Number: 279640
$34.29
In Stock
Idler Pulley
★★★★★
★★★★★
(84)
Part #279640
This Idler Pulley includes the tri-ring and gasket and everything included here is manufacturer-certified. This part maintains correct tension on the drive belt in order to spin the drum properly. If damaged or broken the dryer will not dry properly, will not tumble properly, or may not even start. Installation is rated as "Medium" difficulty. This part is located on the dryer drum, around the tension pulley. Refer to your user manual and model number for repair instructions and to ensure this part is right for you. For this repair project, the tools needed are a Phillips screwdriver, 1/4 inch nut driver, putty knife, small flat blade screw driver, and needle nose pliers.
Dryer Drum Support Roller – Part Number: WPW10314173
$28.21
In Stock
Dryer Drum Support Roller
★★★★★
★★★★★
(15)
Part #WPW10314173
This genuine OEM dryer drum support roller is designed to hold the drum in place while allowing it to rotate smoothly and quietly during operation. Built for durability and reliable performance, it helps reduce noise and ensures consistent tumbling. Ideal for replacing worn or damaged rollers, it resolves issues such as squeaking, rumbling, or poor drum movement, helping restore efficient and dependable dryer operation.
Dryer Thermostat Internal bias – Part Number: WP8577274
$45.05
In Stock
Dryer Thermostat Internal bias
★★★★★
★★★★★
(24)
Part #WP8577274
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
Leveling Foot – Part Number: 49621
$10.95
In Stock
Idler Pulley with Bracket – Part Number: W10837240
$41.14
In Stock
Idler Pulley with Bracket
★★★★★
★★★★★
(50)
Part #W10837240
This idler pulley assembly includes the pulley and bracket, ensuring proper tension on the dryer drive belt for smooth drum rotation. Compatible with several Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dryers, this OEM part is ideal for replacing damaged components. Disconnect power before installation.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Dryer Radiant Flame Sensor – Part Number: WP338906
$49.45
In Stock
Dryer Radiant Flame Sensor
★★★★★
★★★★★
(6)
Part #WP338906
This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.
Blower Wheel – Part Number: WP697772
$70.35
In Stock
Blower Wheel
★★★★★
★★★★★
(18)
Part #WP697772
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.
Air Conditioner Cover Screw – Part Number: WP308685
$10.95
In Stock
Air Conditioner Cover Screw
Part #WP308685
Sold individually.
Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272 – Part Number: WPW10359272
$65.95
In Stock
Drum Support Shaft - Rear Shaft with Left Hand Threads WPW10359272
★★★★★
★★★★★
(3)
Part #WPW10359272
Shaft for dryer drum support roller. Rear shaft with left hand threads. Part is updated so nuts may need to be replaced as well on older dryers.
Screw - 10-16 x 1 – Part Number: WP3387230
$10.44
In Stock
Screw - 10-16 x 1
★★★★★
★★★★★
(2)
Part #WP3387230
This screw is sold individually.
Drum Support Roller Shaft - Right Hand Threads – Part Number: WPW10359271
$65.95
In Stock
Drum Support Roller Shaft - Right Hand Threads
Part #WPW10359271
This shaft is for the front with right hand thread. Sold individually.

Common Symptoms of the 11071633610

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Very Loud Squeaking Noise
79 of 100 people found this instruction helpful.
  • GREGORY from Wilsonville, OR
  • Easy
  • 15 - 30 mins
  • Nutdriver, Pliers, Screw drivers
1) Disconnected power cord from wall. 2) Disconnected vent hose from back of dryer. 3)Removed dryer rear panel. 4)Disengaged tension spring on idle wheel arm. 5) Removed worn idle wheel. 6)Installed new Idler wheel assembly. 7) Vacuumed dust from rear of dryer (optional, recommended). 8) Reinstalled rear cover, vent hose and power cord. E asy repair 15-30
Was this helpful?
Thank you for voting!
TOb stopped turning after a week or so of high pitched "squeals" coming from inside the dryer.
43 of 48 people found this instruction helpful.
  • Robert from Princeton, WV
  • Really Easy
  • Less than 15 mins
  • Nutdriver, Screw drivers
I recommend you order the idler pulley as soon as you start to hear the unusual noise indicating metal against metal. Replace the idler pulley before it fails and possibly causes more damage to the drive system. Simply removed the power cord at the back of the dryer and then the multiple screws holding the back panel in place as well as the clip holding the exhaust vent in place. You may need to remove the top panel to access a few of these screws. A diagram of the belt routing is in the paperwork I found behind the front lower panel of the dryer. This too is easily removed with just a few screws.
Was this helpful?
Thank you for voting!
Gas Flame Would Drop Out
49 of 66 people found this instruction helpful.
  • FRED from BRIELLE, NJ
  • A Bit Difficult
  • 15 - 30 mins
  • Nutdriver, Screw drivers
First it was a process of alimination to find out why it was dropping out. After the problem was found it was just a matter of replacing the holding coil on the gas valve. Thank you fred kenney sr
Was this helpful?
Thank you for voting!