11071112020 Kenmore Dryer - Overview

Diagrams for 11071112020

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Drum Support Roller – Part Number: WPW10314173
$28.21
In Stock
Dryer Drum Support Roller
★★★★★
★★★★★
(15)
Part #WPW10314173
This genuine OEM dryer drum support roller is designed to hold the drum in place while allowing it to rotate smoothly and quietly during operation. Built for durability and reliable performance, it helps reduce noise and ensures consistent tumbling. Ideal for replacing worn or damaged rollers, it resolves issues such as squeaking, rumbling, or poor drum movement, helping restore efficient and dependable dryer operation.
Lint Filter – Part Number: W10120998
$62.65
In Stock
Lint Filter
★★★★★
★★★★★
(68)
Part #W10120998
This dryer lint filter is designed to capture lint and debris during the drying cycle, helping maintain airflow and prevent potential fire hazards. Measuring approximately 12.5 inches wide by 10.5 inches deep, it fits securely into the designated slot within compatible dryer models. Regular inspection and replacement of the filter are essential for optimal performance. Installation is tool-free—simply remove the old filter and insert the new one. During replacement, it's recommended to check the filter slot for any accumulated lint, which should be cleared to ensure safe and efficient operation.
Dryer Thermostat Internal bias – Part Number: WP8577274
$45.05
In Stock
Dryer Thermostat Internal bias
★★★★★
★★★★★
(24)
Part #WP8577274
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
M Series New Style Coil Kit – Part Number: 279834
$36.25
In Stock
M Series New Style Coil Kit
★★★★★
★★★★★
(43)
Part #279834
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them as a set. Both have to be operational for the gas valve to open.
Idler Pulley with Bracket – Part Number: W10837240
$41.14
In Stock
Idler Pulley with Bracket
★★★★★
★★★★★
(50)
Part #W10837240
This idler pulley assembly includes the pulley and bracket, ensuring proper tension on the dryer drive belt for smooth drum rotation. Compatible with several Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dryers, this OEM part is ideal for replacing damaged components. Disconnect power before installation.
Moisture Sensor – Part Number: WP3387223
$15.29
In Stock
Moisture Sensor
★★★★★
★★★★★
(11)
Part #WP3387223
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Dryer Drum Seal with Adhesive – Part Number: 280114
$61.07
In Stock
Dryer Drum Seal with Adhesive
★★★★★
★★★★★
(29)
Part #280114
This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.
Outlet Screen Door Grille – Part Number: W11086603
$41.95
In Stock
Outlet Screen Door Grille
★★★★★
★★★★★
(16)
Part #W11086603
Protect your clothes and keep your dryer running smoothly with this replacement screen door grille. As the top cover for the lint filter, it helps prevent snags and supports proper airflow. If your current grille is cracked or broken, it could lead to damaged clothing or reduced drying performance. This plastic cover is sold individually and does not come with mounting screws, so be sure to check your existing setup before ordering.
Refrigerator Light Bulb 10w – Part Number: WP22002263
$28.08
In Stock
Refrigerator Light Bulb 10w
★★★★★
★★★★★
(10)
Part #WP22002263
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Whether you're replacing a bulb in your Whirlpool or another compatible brand, this one fits right in. Just twist it into place—no tools needed. For safety, make sure your appliance is turned off before swapping the bulb.
Dryer Radiant Flame Sensor – Part Number: WP338906
$49.45
In Stock
Dryer Radiant Flame Sensor
★★★★★
★★★★★
(6)
Part #WP338906
This part senses if the igniter is hot enough to ignite the flame for heat, allowing the gas valve to open. The sensor is three inches long and is used for many gas clothes dryers. If your dryer is not creating any heat, taking too long to dry or shuts off too soon, you may need to replace the flame sensor. This is a genuine OEM part and is made of both plastic and metal. Please remember to disconnect power to your dryer before starting your repair.
Igniter Kit – Part Number: 279311
$51.90
In Stock
Igniter Kit
★★★★★
★★★★★
(13)
Part #279311
This silicone carbide igniter with ceramic holder kit includes the 3" flat igniter, bracket, 4" wire leads, and the plug. It can replace both round and flat igniters. This kit is used for many gas clothes dryers.

Common Symptoms of the 11071112020

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer ran but would not heat
422 of 482 people found this instruction helpful.
  • Gary from Haverhill, NH
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers, Socket set
PartSelect showed seven different possibilities why the dryer wouldn't heat. I removed the two screws to remove the bottom panel and turned the dryer on and noticed that the heating element that ignites the gas was working fine. This meant that it was not getting gas so it could be the gas valve or one of the two gas valve coils which are located on top of the gas valve. I borrowed my neighbor"s ohm meter and touched the two probes on the coils terminals to check for continuity and found that one of the coils read zero. I then took both of the coils out by removing two screws and tested each coil again. One coil read 500-850 and the other read zero. This meant that it was no good so I called for the part and received it in three days. I reassembled the parts and turned the dryer on and it fired up after a few seconds. It works as good as new. The part plus shipping was less than $30. My repairman would have charged me $150-$200. While the dryer was apart I gave it a good cleaning with a vacuum and a toothbrush in delicate areas. I also removed and cleaned the lint trap housing by removing two nuts. I didn't know much about gas dryers, but thanks to PartSelect I easily fixed it myself.
Was this helpful?
Thank you for voting!
Dryer flame goes out after about 8-minutes from start and won’t work again until a 15-minute rest.
220 of 248 people found this instruction helpful.
  • andy from Bethesda, MD
  • Easy
  • 30 - 60 mins
  • Screw drivers
There was no problem with lint build-up within the dryer & the exhaust vent. I removed the gas cycling thermostat & thermal fuse from system & dryer still was not operating correctly. The radiant sensor & hi-limit thermostat both seemed to be operating correctly. That left either of the two coils as the culprits. I replaced both coils & the problem was corrected.
Was this helpful?
Thank you for voting!
felt strip came off lint screen
223 of 279 people found this instruction helpful.
  • JEFFREY from FALL RIVER, MA
  • Really Easy
  • Less than 15 mins
ordered new lint screen, removed old screen, inserted new screen.
Was this helpful?
Thank you for voting!