11061652020 Kenmore Dryer - Overview

Diagrams for 11061652020

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Dryer Heating Element – Part Number: WP3387747
$85.75
In Stock
Dryer Heating Element
★★★★★
★★★★★
(73)
Part #WP3387747
When connected to electricity the dryer heating element glows red hot and generates heat. When air is blown over it, it heats the air which is used to dry the clothes. The heating element fits inside the heater housing inside the dryer. Wear and tear on the heater coil from use will eventually cause the coil to break and the element to fail. When this part fails it can cease to produce any heat. Alternately, the coil could break and short to ground allowing the dryer to continue to heat even when turned off. The latter is a fire hazard and the dryer should be disconnected from power until the element is replaced. If the element coil breaks, the element needs to be replaced. This model is 11 by 5 inches with 5/16” terminals, metal and ceramic, and comes in black. It is sold individually.
Dryer Drum Support Roller – Part Number: WPW10314173
$28.21
In Stock
Dryer Drum Support Roller
★★★★★
★★★★★
(15)
Part #WPW10314173
This genuine OEM dryer drum support roller is designed to hold the drum in place while allowing it to rotate smoothly and quietly during operation. Built for durability and reliable performance, it helps reduce noise and ensures consistent tumbling. Ideal for replacing worn or damaged rollers, it resolves issues such as squeaking, rumbling, or poor drum movement, helping restore efficient and dependable dryer operation.
Lint Filter – Part Number: W10120998
$62.65
In Stock
Lint Filter
★★★★★
★★★★★
(68)
Part #W10120998
This dryer lint filter is designed to capture lint and debris during the drying cycle, helping maintain airflow and prevent potential fire hazards. Measuring approximately 12.5 inches wide by 10.5 inches deep, it fits securely into the designated slot within compatible dryer models. Regular inspection and replacement of the filter are essential for optimal performance. Installation is tool-free—simply remove the old filter and insert the new one. During replacement, it's recommended to check the filter slot for any accumulated lint, which should be cleared to ensure safe and efficient operation.
Dryer Thermostat Internal bias – Part Number: WP8577274
$45.05
In Stock
Dryer Thermostat Internal bias
★★★★★
★★★★★
(24)
Part #WP8577274
This thermostat may differ in appearance, but functions the same as the original part. This part controls the temperature of the inside of the dryer drum and prevents the dryer from overheating.
Idler Pulley with Bracket – Part Number: W10837240
$41.14
In Stock
Idler Pulley with Bracket
★★★★★
★★★★★
(50)
Part #W10837240
This idler pulley assembly includes the pulley and bracket, ensuring proper tension on the dryer drive belt for smooth drum rotation. Compatible with several Whirlpool, KitchenAid, Maytag, Jenn-Air, Amana, Inglis, and Magic Chef dryers, this OEM part is ideal for replacing damaged components. Disconnect power before installation.
Moisture Sensor – Part Number: WP3387223
$15.29
In Stock
Moisture Sensor
★★★★★
★★★★★
(11)
Part #WP3387223
This is the moisture sensor for your dryer. It helps detect the amount of moisture in your clothes during the dryer cycle. If you notice your clothes are still wet after an automatic dryer cycle is done, you may need to replace the sensor. You will find the moisture sensor behind the lint screen. Be sure to disconnect the power source from the dryer before you begin this repair. Note: Some model's require two sensors, please order quantity needed. Sensor only, harness is not included. This part is sold individually.
Roller Support Tri-Ring – Part Number: WPW10512946
$18.70
In Stock
Roller Support Tri-Ring
★★★★★
★★★★★
(4)
Part #WPW10512946
If you notice that your dryer is noisy or will not tumble, you may need to replace the tri ring. This part is triangular, and is less than an inch in size. Tri rings can be found both on the idler pulley shaft, or on the rear drum roller shaft. In either case, you will need to remove the front panel of the dryer and the drum to access the part for repair. Once you have accessed the damaged tri ring, you will simply need to slip it off and replace it with the new one. This part is sold individually. Be sure to disconnect the power source from the dryer before you begin this repair.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(23)
Part #72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
Dryer Drum Seal with Adhesive – Part Number: 280114
$61.07
In Stock
Dryer Drum Seal with Adhesive
★★★★★
★★★★★
(29)
Part #280114
This part seals the drum to prevents air from escaping. This includes silicone rubber adhesive.
Outlet Screen Door Grille – Part Number: W11086603
$41.95
In Stock
Outlet Screen Door Grille
★★★★★
★★★★★
(16)
Part #W11086603
Protect your clothes and keep your dryer running smoothly with this replacement screen door grille. As the top cover for the lint filter, it helps prevent snags and supports proper airflow. If your current grille is cracked or broken, it could lead to damaged clothing or reduced drying performance. This plastic cover is sold individually and does not come with mounting screws, so be sure to check your existing setup before ordering.
Refrigerator Light Bulb 10w – Part Number: WP22002263
$28.08
In Stock
Refrigerator Light Bulb 10w
★★★★★
★★★★★
(10)
Part #WP22002263
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Whether you're replacing a bulb in your Whirlpool or another compatible brand, this one fits right in. Just twist it into place—no tools needed. For safety, make sure your appliance is turned off before swapping the bulb.
Blower Wheel – Part Number: WP697772
$70.35
In Stock
Blower Wheel
★★★★★
★★★★★
(18)
Part #WP697772
The blower wheel pulls air over the heat source, through the clothes drum, and past the thermostats, then pushes it out the exhaust duct. The blower wheel, which is usually plastic, may wear out over time. But if it's noisy, it may simply be clogged with lint. Clean the blower and test to see if the dryer is still noisy. If it is, you probably need to replace it.

Common Symptoms of the 11061652020

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Burned out heater element
526 of 625 people found this instruction helpful.
  • Alan from Brooksville, FL
  • Easy
  • 30 - 60 mins
  • Socket set
Remove the kick plate from the bottom of the dryer by sliding a putty knife along the top edge to release the plastic clamps, one on each side about 4" in from the edges. The kick plate folds out and down. You will see the heat shield on the right, held in by one hex head screw. Remove screw and heat shield. The element is positioned in a n open-front housing and is fastened to the left side of the housing by two hex head screws, located on the "rail" of the element and right near the two wires. Remove the hex-head screws that hold the element in place and disconnected the two wires by pulling them out by hand or with needle nose pliers. The only difficulty here is the cramped working area...I recommend a stubby socket driver for these two screws. Most of this I had to do by feel because I could not see the screw heads. Once the screws are out and the wires have been disconnected, slide the old element straight out toward you. You may need to disconnect a small plastic hose located to the left front of the element, but this hose just pulls right off. Vacume the dust & lint build-up out of the whole area, wipe out the element housing and clean up the whole underside of the dryer prior to installing the new element. Installation is reverse of removal. It also might be a good opportunity to clean out your exhaust duct and the vent to the outside. (Never use the aluminum foil-accordian-type duct.) If the exterior dryer vent has any kind of screen over it, remove it and get rid of it. Screens collect lint, lint builds up and burns out elements.
Was this helpful?
Thank you for voting!
felt strip came off lint screen
223 of 279 people found this instruction helpful.
  • JEFFREY from FALL RIVER, MA
  • Really Easy
  • Less than 15 mins
ordered new lint screen, removed old screen, inserted new screen.
Was this helpful?
Thank you for voting!
Felt gasket on lint filter loose...
61 of 71 people found this instruction helpful.
  • Catherine from Atascadero, CA
  • Really Easy
  • Less than 15 mins
Found this site by googling, and it works! I searched lint filters and just ordered based on how it looked...LOL! Husband wasn't home, it looked pretty much like the one I had in my hand, so.... I ordered it. It is the perfect fit and seems to have a tighter gasket glued in all around the screen. Let's hope this one lasts longer than 6 mo nths! Thank you Parts Select for being so fast!! Filter got here in less than 48 hrs.!
Was this helpful?
Thank you for voting!