1106110800 Kenmore Washer Dryer Combo - Overview

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Refrigerator Light Bulb 10w – Part Number: WP22002263
$28.08
In Stock
Refrigerator Light Bulb 10w
★★★★★
★★★★★
(10)
Part #WP22002263
Brighten up your appliance with this easy-to-install 10-watt light bulb, perfect for dryers and refrigerators. It gives off a clear, steady light so you can easily see inside when the door is open. Whether you're replacing a bulb in your Whirlpool or another compatible brand, this one fits right in. Just twist it into place—no tools needed. For safety, make sure your appliance is turned off before swapping the bulb.
Washer Hose Clamp – Part Number: WP596669
$11.52
In Stock
Washer Hose Clamp
Part #WP596669
Hose Clamp – Part Number: WP285655
$15.68
In Stock
Hose Clamp
Part #WP285655
This hose clamp is sold individually.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Refrigerator Screw – Part Number: WP98165
$10.95
In Stock
Refrigerator Screw
Part #WP98165
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Oil Seal Kit for Gearcase Input Shaft – Part Number: 285352
$59.35
In Stock
Oil Seal Kit for Gearcase Input Shaft
★★★★★
★★★★★
(1)
Part #285352
This two piece oil seal kit comes in two pieces and is used for the gearcase input shaft of your washer.
Washer Hose Clamp – Part Number: WP616099
$14.28
In Stock
Washer Hose Clamp
Part #WP616099
Note: This part has been updated by the manufacturer. It may appear different but will still function the same as the original.
Front Top Lock – Part Number: WP18776
$18.95
In Stock
Front Top Lock
★★★★★
★★★★★
(1)
Part #WP18776
This part is used to secure the top panel to the cabinet. Sold individually.
Range Hex Nut – Part Number: WP488130
$12.05
Special Order
Range Hex Nut
Part #WP488130
Part may differ in appearance, but functions same as original.
Water Inlet Hose Washer – Part Number: WP16123
$10.47
Special Order
Water Inlet Hose Washer
Part #WP16123
Sold Individually. Order quantity needed.
Washer Water Pressure Hose Cut to Fit – Part Number: WP353244
$63.75
In Stock
Washer Water Pressure Hose Cut to Fit
★★★★★
★★★★★
(2)
Part #WP353244
This is the hose that tells your appliance if your tub is at the desired water level.
Hose Washer  Kit – Part Number: 285452A
$10.47
In Stock
Hose Washer Kit
Part #285452A
Washer fill hose gasket and screen. This is a set of 4.

Common Symptoms of the 1106110800

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken clip on top panel hold down
15 of 26 people found this instruction helpful.
  • Mark from Huntington Station, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Dryer Top Panel is Loose
5 of 5 people found this instruction helpful.
  • MONTE from CHESAPEAKE, VA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
Was this helpful?
Thank you for voting!
Bulb worked for a couple days and has now burned out, filaments dangling
3 of 4 people found this instruction helpful.
  • Amy from JUNCTION, TX
  • Easy
  • Less than 15 mins
  • Screw drivers
To replace the light bulb, I removed the screw and the cover, unscrewed the old bulb, replaced with the new bulb and replaced the cover, securing it with the small screw. It worked appropriately with normal use for a few days and then I noticed the light was not coming on when I opened the door.

I removed the cover and pulled out the bulb to find that the filaments inside are dangling and burned through. I need them replaced, please.
Was this helpful?
Thank you for voting!