1105907100 Kenmore Dryer - Overview

Diagrams for 1105907100

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid Switch – Part Number: W10820036
$33.28
In Stock
Lid Switch
★★★★★
★★★★★
(7)
Part #W10820036
Keep your washer or dryer running safely with this easy-to-install lid or door switch kit. It stops the machine from working when the door is open, helping prevent spills and accidents. Compatible with many models, this small but important part fits neatly inside your appliance and comes with everything you need for installation. Just unplug your machine, swap out the old switch, and you're good to go. It’s about 2.5 inches long and blends in with most interiors.
Thrust – Part Number: WPW10121334
$9.85
In Stock
Cycling Thermostat - Limit 135/155 – Part Number: WP694674
$67.05
In Stock
Cycling Thermostat - Limit 135/155
★★★★★
★★★★★
(3)
Part #WP694674
If your dryer isn’t heating properly, this adjustable thermostat kit could be the solution. It helps keep the dryer at the right temperature by turning the heat on and off as needed. You can set it anywhere between 135°F and 155°F, and it kicks the heat back on when the temperature drops by 20°F. The kit comes with everything you need—thermostat, jumper wires, and wire nuts—and is a great fix for dryers that aren’t warming up like they should.
Front Top Lock – Part Number: WP18776
$18.95
In Stock
Front Top Lock
★★★★★
★★★★★
(1)
Part #WP18776
This part is used to secure the top panel to the cabinet. Sold individually.
Dryer Clampmotor – Part Number: WP660658
$15.35
In Stock
Dryer Clampmotor
Part #WP660658
This clamp is used to secure the drive motor.
Dryer Screw – Part Number: WP681414
$10.95
In Stock
Dryer Screw
Part #WP681414
This screw is sold individually.
SEAL-DOOR – Part Number: W11613302
$49.95
Special Order
SEAL-DOOR
Part #W11613302
Adhesive sold separately.
Pressure Regulator – Part Number: WP4454571
No Longer Available
Pressure Regulator
Part #WP4454571
This valve will automatically cut off the flow of gas when it reaches a certain pressure.
Dryer Gas Valve Limiter – Part Number: 661580
$163.98
Special Order
Dryer Gas Valve Limiter
Part #661580
This gas valve limiter is for dryers. Gas valve limiter opens to release excess pressure from the gas valve if the gas supply pressure exceeds the normal rating. Unplug the dryer and shut off the gas supply before installing this part. Wear work gloves to protect your hands.
RIVET – Part Number: 98669
No Longer Available
RIVET
Part #98669
CLAMP – Part Number: 341029
$24.95
Special Order
CLAMP
Part #341029

Common Symptoms of the 1105907100

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Lid closes, switch wouldn't turn on machine.
31 of 47 people found this instruction helpful.
  • Kenneth from Wilmington, IL
  • Easy
  • 1- 2 hours
  • Nutdriver, Screw drivers, Socket set
Used toothpick for a year to push switch acctuator far enough to engage switch. Broke my foot and found time to order part thru PartSelect. Went from cast to boot and received part 2 days after ordered. Had difficulty with foot and getting to switch. Went back into PartSelect and figured out how to dis-assemmble panels thru the diagrams. Time on my job doesn't, just that their service and expertise that is available to everyone is there to use. Broken bones or not, I will always get my parts and advice from PartSelect. Thanks to PartSelect.
Was this helpful?
Thank you for voting!
Washer would fill up, wash, then stop
22 of 31 people found this instruction helpful.
  • Glen from Plano, TX
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
I deduced the lid switch was the problem.

I removed the two screws holding the control panel on. Pulled the control panel back.
Disconnected the ground wire of the lid switch.
removed the two top clamps that hold the panel to the top of the machine.
Pulled back the casing (outside of the washer) and placed it on it's side on the floor. Here I could reach the switch. Removed old, installed new and reversed the process.

The part that gave me the biggest problem was setting the casing back on to the frame. You have to slide the front part in at the bottome, then lean back the rest of it.
Was this helpful?
Thank you for voting!
Temperature setting not working
19 of 23 people found this instruction helpful.
  • Robert from Buffalo, NY
  • Easy
  • 30 - 60 mins
  • Nutdriver, Screw drivers
Took off back cover, thermostat was easily identified because of photos I've seen on website. Took 2 connectors off, removed 2 screws and removed old thermostat. That was pretty much it!

NOTE: Replacement thermostat 694674 has an adjustable temperature range setting that MUST be manually set prior to installing! You need to use the enclosed chart to find your original part# and make sure the setting is matched. My original part# 341146 had a "D" setting so I had to change but very easy to do.
Was this helpful?
Thank you for voting!