1105904251 Kenmore Washer - Overview

Diagrams for 1105904251

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hose Clamp – Part Number: WP285655
$15.68
In Stock
Hose Clamp
Part #WP285655
This hose clamp is sold individually.
Washer Transmission Stem Seal – Part Number: WP8577376
$14.25
In Stock
Washer Transmission Stem Seal
Part #WP8577376
Sold individually.
Dryer Screw – Part Number: WP90767
$10.40
In Stock
Dryer Screw
Part #WP90767
This screw is sold individually.
Refrigerator Screw – Part Number: WP98165
$10.95
In Stock
Refrigerator Screw
Part #WP98165
This screw is a little under an inch long and is made of metal. It is used with a refrigerator's ice maker assembly. Sold individually.
Lid Hinge Mounting Screw – Part Number: WPW10119828
$9.85
In Stock
Lid Hinge Mounting Screw
Part #WPW10119828
Sold individually. NOTE: The color on the screw may not be the same as the image, but will still function the same.
Washer Hose Clamp – Part Number: WP356138
$15.07
In Stock
Washer Hose Clamp
Part #WP356138
This clamp helps to prevent leaking by holding the end of water hose in place.
Washer Spanner Nut – Part Number: WP21366
$20.48
In Stock
Washer Spanner Nut
Part #WP21366
If your washer is noisy or shaking, the spanner nut might need replacing. This part locks the inner tub to the drive block so it spins smoothly during cycles. It has a right-hand thread and is easy to install with basic tools—just make sure the washer is unplugged and water is turned off before you start. A simple fix for a quieter, more efficient wash.
Dryer Support Roller Clip – Part Number: WP90296
$10.95
In Stock
Dryer Support Roller Clip
Part #WP90296
Sold Individually.
Front Top Lock – Part Number: WP18776
$18.95
In Stock
Front Top Lock
★★★★★
★★★★★
(1)
Part #WP18776
This part is used to secure the top panel to the cabinet. Sold individually.
Lid Hinge Bearing – Part Number: WP21258
$14.99
In Stock
Lid Hinge Bearing
Part #WP21258
This is the bearing for the lid hinge. Sold individually.
Washer Water Pressure Hose Cut to Fit – Part Number: WP353244
$63.75
In Stock
Washer Water Pressure Hose Cut to Fit
★★★★★
★★★★★
(2)
Part #WP353244
This is the hose that tells your appliance if your tub is at the desired water level.
Dryer Screw – Part Number: WP681414
$10.95
In Stock
Dryer Screw
Part #WP681414
This screw is sold individually.

Common Symptoms of the 1105904251

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
broken clip on top panel hold down
15 of 26 people found this instruction helpful.
  • Mark from Huntington Station, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
pressed clip into hole on top of front panel. first remove two philip screws that hold filter so you can lift top up.
Was this helpful?
Thank you for voting!
Dryer Top Panel is Loose
5 of 5 people found this instruction helpful.
  • MONTE from CHESAPEAKE, VA
  • Very Easy
  • Less than 15 mins
  • Pliers, Screw drivers
1) Unplug power cable from dryer.
2) Remove the 2 screws that secure the chute for lint filter screen with
Phillips head screwdriver.
3) Remove the lint filter screen.
4) Depress plastic locking clip on each side with putty knife to release
tension and lift up top panel to clear the locking clips. Each locking
clip is located 2-1/2 inches from the front edge of side panel.
5) Lift the top panel and lean against the wall for support. If dryer top
panel cannot be raised all the way due to cabinet(s) above, tape
the dryer top panel to cabinet above or have somebody hold the
top panel for temporary support.
6) Install the new metal locking clips. Ensure that the elongated tab
of the metal locking clip is towards the front of dryer. Compress
locking clip lightly with pliers and push down into the hole.
7) Lower the dryer top panel and press it down in place over the metal
locking clips for a tight fit.
8) Reinstall the 2 screws to secure the lint filter chute.
9) Reinstall lint filter screen.
10) Reconnect power cable for dryer.
11) Turn on dryer and inspect that all dryer panels (top, sides and
front) are tight and secured.
Repair Duration: 5 minutes
Was this helpful?
Thank you for voting!
machine wouldn't turn on when lid closed
2 of 3 people found this instruction helpful.
  • Ellen from NYACK, NY
  • Easy
  • Less than 15 mins
  • Screw drivers
replaced missing screw and pad and now machine works perfectly
Was this helpful?
Thank you for voting!