1104756 Kenmore Washer - Overview

Models starting with 1104756

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Washer Drain Pump – Part Number: WPW10730972
$193.74
In Stock
Washer Drain Pump
★★★★★
★★★★★
(127)
Part #WPW10730972
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. It has two ports for water to pass through: a large one, and a smaller one. This pump also comes with a removable filter.
Front Load Washer Bellow - Gray – Part Number: WPW10111435
$193.84
In Stock
Front Load Washer Bellow - Gray
★★★★★
★★★★★
(42)
Part #WPW10111435
Also known as a door boot seal.This part is used to keep the clothes inside the tub during the wash cycle. The folds in the bellow allow the tub to move separately from the door during the spin cycle.
Touch-Up Paint - White – Part Number: 72017
No Longer Available
Touch-Up Paint - White
★★★★★
★★★★★
(23)
Part #72017
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
Door Strike/Hook – Part Number: WP8540221
$16.14
In Stock
Door Strike/Hook
★★★★★
★★★★★
(14)
Part #WP8540221
Used to help make the door stay closed. Sold individually.
HOSE – Part Number: W11366249
$51.65
In Stock
HOSE
★★★★★
★★★★★
(32)
Part #W11366249
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens you will notice water leaking onto the floor. The tub-to-pump hose is found below the washer tub. To disconnect the hose, you will need to release the clamps that hold it in place with a pair of pliers. When you replace the tub hose, you will need to transfer the ball, air chamber, and clamps from the old pump to the new one. To do this, you will need a set of wire cutters and a new zip tie to replace the one you will need to cut.
Washer Dispenser Hose – Part Number: W11366227
$35.15
In Stock
Washer Dispenser Hose
★★★★★
★★★★★
(25)
Part #W11366227
This dispenser hose is for washers and carries the contents of the dispenser drawer to the washer tub.
Washer Water Inlet Valve – Part Number: WP8540751
$81.35
In Stock
Washer Water Inlet Valve
★★★★★
★★★★★
(21)
Part #WP8540751
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature or amount of water needed.
Washer Door Lock Latch – Part Number: WPW10253483
$238.50
In Stock
Washer Door Lock Latch
★★★★★
★★★★★
(22)
Part #WPW10253483
If your washer door won’t close or lock, or your machine won’t start, this door latch might be the issue. It’s the part that keeps the door shut tight during the cycle and makes sure everything runs safely and smoothly. Made from tough plastic and metal, it’s built to last and helps prevent leaks and interruptions. It locks and unlocks automatically, so you don’t have to think about it—just make sure it fits your model before ordering, and unplug your washer before installing.
Bellow To Tub Clamp – Part Number: WP8540108
$34.62
In Stock
Bellow To Tub Clamp
★★★★★
★★★★★
(3)
Part #WP8540108
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place on the washer frame. The main reason you would want to replace the bellow clamp is if it is rusted or damaged, and it is not holding the bellow in place. To remove the bellow clamp, simply use a screwdriver to pop the bellow clamp out of the groove it rests in. Place the new clamp back into the bellow groove until it snaps into place. This is an OEM part from the manufacturer.
Washer Drive Belt – Part Number: WP8540101
$54.95
In Stock
Washer Drive Belt
★★★★★
★★★★★
(24)
Part #WP8540101
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is found between the motor pulley and the drive pulley, and it connects the motor to the drive system. When the belt is running, it allows the basket or tub to spin. If the belt is stretched, worn, or broken, the tub will not turn. A warped belt can also cause the washer to be noisy while operating. This part is an authentic OEM part sourced directly from the manufacturer.
Washer Front Leveling Foot – Part Number: WPW10001130
$9.85
In Stock
Tub Baffle – Part Number: WP8540360
$86.60
In Stock
Tub Baffle
★★★★★
★★★★★
(11)
Part #WP8540360
This is the replacement tub baffle for your washer. It is made of black plastic and is approximately 13 inches by 2 inches. This part is sold individually and is an OEM part sourced directly from the manufacturer. The tub baffle is found inside the washer tub, and it helps tumble your clothes. If the baffle is damaged or missing, you may notice marks being left on your clothes. The main reason you would replace the baffle is if you notice these marks, or if the baffle is broken, or keeps falling off.

Common Symptoms of models starting with 1104756

How this model fails, and the parts that fix it.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
F 21 error
377 of 427 people found this instruction helpful.
  • Andrew from St.Louis, MO
  • Easy
  • 15 - 30 mins
  • Screw drivers, Socket set
Removed the front panel unplugged
The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Was this helpful?
Thank you for voting!
Water leak from bottom of door.
201 of 224 people found this instruction helpful.
  • Marty from Belfair, WA
  • Easy
  • 30 - 60 mins
  • Nutdriver, Pliers, Screw drivers
I discovered water leaking from the bottom of the door on our Kenmore front load washer. I did a little self diagnosis from the internet and found that this seems to be a common problem for front load Kenmore washers and that the ususal suspect is the large rubbery bellows. I examined the bellows on my washer and although I didn't find anything wrong with it, I couldn't find any other likely causes. I shopped around and found PartSelect to be the cheapest for the replacement part. Removal is easy by removing the lower front panel with three small screws on the bottom front, then remove the very top panel and then the top front control panel and finally the door panel. the bellows are actually held in place with a spring loop on the outer and a screw tightener on the inner, both are fairly easy to remove and the bellows comes right off. For installation my best advice is to lube the bellows with a small amount of dishwashing soap in the groove that fits on the washer tub. This will help it slide into place and enables a small amount of sliding fine tuning once it is on. From there it is just a reverse of the removal.
Was this helpful?
Thank you for voting!
water pump failed
98 of 110 people found this instruction helpful.
  • Kurt from Caliente, NV
  • Really Easy
  • 15 - 30 mins
  • Nutdriver, Pliers
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
Was this helpful?
Thank you for voting!