This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This drive hub kit (part number W10528947VP) is for washers.
Drive hub kit W10528947VP connects the spin basket to the spin shaft that spins the basket. The kit may include multiple parts; refer to...
This is a replacement clutch assembly or cam kit for your washer. The clutch assembly is mounted on the drive shaft on the bottom of your washer. You may need to replace the clutch assembly if the spl...
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work glove...
The drain hose carries used water from the washer to your house drain.
$31.80
In Stock
Questions And Answers for 11022352511
Ask our experts a question about this model and we'll get back to you as soon as possible!
11 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Janet
August 10, 2021
When I close the lid it wont stop locking and unlocking and wont let me do anything else, I have unpluged the unit and tried plugging back in a day later but same results
For model number 11022352511
Hello Janet, Thank you for the question. Normally this is an indication the Washing Machine Door Lock Assembly is defective that will need to be replaced. We hope this helps!
Hi Debra, thank you for the question. Yes, your model does have a filter. The part you are looking for is the lint filter, part number PS11750500. We hope this information is useful!
Hi Debra,
Thank you for your question. The lint filter is located under the basket in the bottom of the outer tub. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
James
July 9, 2023
ADGITATOR DOES NOT MOVE WHEN WASHING CLOTHES
For model number 11022352511
Hi James, thank you for reaching out. First, you may need to make sure the agitator is not stuck. If that is not causing the issue, then you may need to replace the drive hub kit, part number PS6012095, as it is most likely faulty. Glad to be of assistance!
(a.) When start button is pressed, and dial is set on Normal.
1. the lock light does not come
2. sounds like a little bit of water starts flowing
3. sounds like it wants to start the cycle- abnormal noise Like gears striped) is heard.
(b.) When Dial is set on Rinse and spin:
1.The door locks and light come on .
2. the spin cycle starts
3. it starts to Rinse
4. What could be the issue,? Thank you
For model number 11022352511
Hi Albert, thank you for reaching out. Based on our research, the issue is most probably with the control board, part number PS12347928. It manages the washer's functions such as filling, washing, draining and spinning. We would suggest replacing it to fix the issue. We hope this helps!
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch and put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned it back up and got caught up on laundry. good day when the washer is fixed.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.