This drive hub kit helps your washer spin and agitate properly by connecting the basket to the motor. If your washer isn’t spinning, is noisy, or wobbles too much, this part might be the fix. It’s a simple DIY repair with easy-to-follow instructions and usually includes everything you need to get your washer working again.
This washing machine suspension rod kit includes 4 suspension rods, 4 suspension balls, and 4 bushings to stabilize the washer tub and minimize vibrations during operation. If the washer shakes or vibrates excessively, replacing the suspension rods may resolve the issue. Installation requires safety precautions, such as unplugging the appliance and wearing work gloves.
If your washer is noisy, spins slowly, or leaves clothes soaking wet, this splutch cam kit might be the fix. It helps your machine switch between washing and spinning by connecting the motor to the basket. The kit includes everything you need—clutch parts, pulley, gear, and more—but make sure it fits your model before ordering. It’s a simple repair that can get your washer back to working like new.
If your washer isn’t spinning or making strange noises, the drive belt might be worn out. This genuine replacement belt connects the motor to the drum, helping it spin and tumble your clothes properly. It fits many Whirlpool, Maytag, and Kenmore models, but be sure to check your model number before ordering. A broken belt can also cause a...Read more burning smell, so replacing it can get your washer back in shape and running smoothly.
This suspension rod kit is a genuine OEM replacement kit that is compatible with various models of washing machine. The kit is responsible for supporting the inner tub of the washing machine and absorbing any excessive vibrations and movement caused during the washing and spinning cycles. This helps to protect the tub and interior of the ...Read morewasher from damage. If the suspension rods in your washer are faulty, you will likely notice loud banging, knocking, or scraping sounds as the tub makes contact with the washer cabinet. Each kit includes four suspension rods and springs as well as the suspension ball cups. It is advised you replace all suspension rods at the same time, as they tend to wear at similar rates.
This water inlet valve is for washers.
The water inlet valve controls the water flow into the washer.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
This shift actuator is an essential component in washing machines, responsible for switching the motor between spin and agitate modes while also communicating spin speed to the control board. A malfunctioning actuator can lead to improper spinning or agitation and may trigger error codes. Made primarily of durable plastic, it features an ...Read moreintegrated 120V/60Hz/2.8W motor for reliable performance. This OEM part is sold individually and is compatible with a variety of washer models. For safety, always disconnect power before installation and follow manufacturer guidelines for replacement.
The transmission drives the agitator and spins the basket in the washer. Possible Repair Solution For: Not washing properly, will not agitate, pumps but will not spin.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Jerry - For model number 11022352510
December 30, 2019
Lid lock broken. Machine will not spin and drain?
Hello Jerry,
Thank you for your question. The lid lock assembly for your model is under part PS12704713. We hope this helps!
Washer makes clicking sound when washing. It also doesn't completely drain water all the time. What may be causing this problem.
Hello Lawrence, thank you for getting in touch. According to our research, we would recommend checking the door lock first. If it is fine, then the issue is most probably with the electronic control board, part number PS12114299. It manages the washer's functions such as filling, washing, draining and spinning. You may need to replace it to fix the issue. We hope this information helps!
Always has balance issues no matter what size of load . Is the sensor the problem
Hi Patty, thank you for contacting us. Based on our understanding of the issue, we would suggest that you make sure the washer is level. If that is not causing the issue, then you may need to check the suspension rods, part number PS12347546, as they are most likely faulty and may need to be replaced. We hope this helps!
Hi Sandy, thank you for writing in. Here are the steps to remove the agitator from your washer...To replace your washers agitator first
0:09
remove the fabric softener dispenser and
0:11
lint cap if applicable to your model
0:16
then use a 7/16 inch socket with a 12
0:19
inch extension to loosen the mounting
0:22
bolt with the bolt loosened pull the old
0:26
agitator up and out
0:32
install the new agitator by first
0:35
inserting the mounting bolt now slide
0:41
the new agitator onto the drive shaft
0:45
and tighten the bolt to secure replace
0:53
the lint cap if necessary and the fabric
0:58
softener dispenser with the new agitator
1:02
installed make sure all tub components
1:04
are functioning properly during the wash
1:06
cycle
We hopw this helps.
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Violent shacking in spin mode.
189 of 230 peoplefound this instruction helpful.
Terry from Homosassa, FL
Really Easy
30 - 60 mins
Pliers, Screw drivers, Wrench (Adjustable)
Watched a video on the internet.
Was this helpful?
Thank you for voting!
Noise on bottom of Washer louder as time went on. 1 1/2 years
95 of 129 peoplefound this instruction helpful.
Jerry from WALLA WALLA, WA
Really Easy
15 - 30 mins
Nutdriver, Screw drivers, Socket set
Well, first investigated and found loose nut on drive clutch. First take off the two screws with nut drive then cover off using a screwdriver blade to snap off the cover. Then socket ratchet to take off the nut on drive clutch. take off belt by slowly rotating the drive gear. two screws that hold the electronics to the upper drive clutch
... Read moreand put aside, so you can snap off the cover for drive clutch on upper part with screwdriver and off the parts come and install whole unit back as took it apart. Line up the new upper clutch so that is position as was before. (Using parts diagram helps a lot as www. partsselect.com has for you or Maytag.com.) Then put the electronic part board back on and the gear and nut. Make sure it is tight by several attempts to make sure it's snugged up good and then slowly roll belt back on the pulley and motor drive. Put your cover guard back on with two screws and done.
Hub had warn its grooved teeth off and washer wouldnt agitate
66 of 93 peoplefound this instruction helpful.
Allison from RICHFORD, NY
Easy
15 - 30 mins
Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
My Orders
