This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
This drive hub kit helps your washer spin and agitate properly by connecting the basket to the motor. If your washer isn’t spinning, is noisy, or wobbles too much, this part might be the fix. It’s a simple DIY repair with easy-to-follow instructions and usually includes everything you need to get your washer working again.
This agitator is for washers.
Agitator rotates back and forth to move the clothes inside the tub to clean the load.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
This lid switch assembly is for a top load washer. The lid switch assembly detects if the washer lid is open or closed and prevents the washer from spinning when the lid is open.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Kelvin - For model number 11022242510
November 8, 2021
My Kenmore series #300 washer is making a loud noise during the spin cycle, what could be the most likely fix for this issue?
Hello Kelvin, Thank you for the question. We suggest checking the Drive Hub Kit for wear or damage. Drive hub kit connects the spin basket to the spin shaft that spins the basket. When damaged it can cause noise. We hope this helps!
Hello!
I Cannot change the “Soil level”, “Rinse” or the type of wash cycle (Delicates etc.). It only goes through a complete cycle on "Normal”. Anything other than that, it will not rinse.
Thanks!
Ron
Hi Ron, thank you for contacting us. The following parts need to be checked to fix the issue: the selector switches, part numbers PS11752017 and PS11752020, and the lint filter, part number PS11750500. If the problem persists, we would suggest checking the control board, part number PS12347409, to fix the issue. We hope this solves your problem!
Are there supposed to be agitator dogs for this model? Machine does not agitate, but when i took the upper agitator and washer plate off, there were no visible traces of dogs, worn or otherwise. I am unable to see any damage to the lower portion of the agitator.
Hello Joel, Thank you for your inquiry. We have researched the model number you have provided, and show that this model does not have agitator dogs. If it is not agitating, we recommend checking the drive belt, the drive hub, the shift actuator, the drive motor and the gearcase transmission. You can test the parts with a multimeter. If you are unfamiliar with how a multimeter functions, we have videos available to assist you. Good luck with your repair.
Can I purchase the drive pulley that sits on the motor the plastic one that wears out and how much will it be for the piece I've got the piece off already I just need to purchase the piece
Hi Roy, thank you for contacting us. According to our research, the part you are looking for is not sold separately. It comes in an assembly with the drive motor, part number PS11726282. We hope that helps!
Was this helpful?
Thank you for voting!
Roy - For model number 11022242510
October 24, 2023
Can the plastic drive pulley that sits on the motor be bought individually
Hi Roy, thank you for contacting us. Based on our research, the part you are referring to comes in an assembly with the motor, part number PS11726282, and is not available separately. Let us know if you have further questions!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Hub had warn its grooved teeth off and washer wouldnt agitate
66 of 93 peoplefound this instruction helpful.
Allison from RICHFORD, NY
Easy
15 - 30 mins
Screw drivers
ordered hub and it shipped quickly. I was able to put the hub in place and screw the screws in. you want to tighten them down slowly and go around to each screw tightening a little at a time so you don't break the hub. as you tighten the screws down the hub slides down flush. its impossible to just push the hub on with your hand. Buttoned
... Read more it back up and got caught up on laundry. good day when the washer is fixed.
Read less
Was this helpful?
Thank you for voting!
Waher would not spin and made noise
25 of 29 peoplefound this instruction helpful.
Andrew from SYLVANIA, OH
Very Easy
Less than 15 mins
Screw drivers, Wrench (Adjustable)
Removed center cap, loosened center nut, pry lightly up on center plate and tap center nut. Center plate comes loose, remove nut, remove center plate. Pry lock clip out and remove, remove screw with electric impact (screw drive will work, but slower), remove drive hub. Install new drive hub (be sure to check screw hole alignment), install
... Read more and tighten screws (be sure to follow a skip pattern and bring it down even), install lock clip, install center plate, install and tighten nut, replace center cap. Done!
Read less
Was this helpful?
Thank you for voting!
washer not agitating
22 of 23 peoplefound this instruction helpful.
David from EAST AMHERST, NY
Easy
15 - 30 mins
Socket set
This was a learning experience but it appears to have worked out in the end. Our 3 1/2 year old washer was not agitating much and I attributed that to a loose bolt. I would tighten the bolt and it would work ok for a load or two and then stop agitating. I would find that the bolt was loose again. I took a number of steps to try to get
... Read more the bolt to stay on tight - threadlock, a new bolt, more threadlock, and applying progressively more force on the bolt, with no better results. Yet the repair guys on you tube were saying the bolt only needs to be snug, not super tight - something was amiss. I even went so far as to secure the basket with a rope so I could use two hands on the socket wrench (please don't do this). But when I tried the washer again there was no agitation at all! I observed the agitation output in manual test mode and the bolt was turning in lock step with the shaft but the agitator wasn't turning at all. That's when I suspected that the problem was actually a worn lower agitator. Trouble was that now I couldn't seem to get the bolt off. Turning the wrench caused the shaft itself to rotate so I couldn't loosen the bolt from the shaft. I thought I broke the washer. Then I considered that maybe the shaft was rotating because the washer was in an agitation mode when I turned it off. I went back into manual test mode, made the washer spin, then turned it off. Fortunately, this worked. The shaft was again stationary and, albeit with great difficulty, I got the bolt off.
I removed the agitator, and as a pro would have figured out long before, the ridges inside the top of the lower agitator were almost completely worn down. I realized then that the contact between these ridges and the splines on the shaft is what is supposed to cause the lower agitator to move with the shaft. The purpose of the bolt is just to keep the agitator in the correct position and from coming off the shaft. I had been trying to compensate for the worn agitator ridges by over-tightening the bolt, creating some contact at the top of the shaft. This would work for a little while, then the agitator would start slipping, and the slipping agitator was acting just like a wrench loosening the bolt (until my stupid rope trick, that is.)
So I ordered a new agitator (only the lower agitator was bad, but the price of an entire agitator isn't a lot more than just the lower part and I was reading that the upper agitator parts will wear over time) and another new bolt (because my repeated attempts to over-tighten the first one I ordered had split the rubber gasket apart and worn the bolt head).
The new agitator fit snugly on the splines of the shaft so I sensed no need to use excessive force on the bolt. Just an easy one-handed snug tightening with the socket wrench, using the other hand to hold the lower agitator. The washer is now working again.
My Orders
