This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, and freezers. This is a genuine OEM part and includes a brush applicator. Please remember to wear gloves to protect your hands when applying this paint.
This hinge bracket, also known as a door stop, is attached to the bottom of the door and is used to limit how far the door swings out to protect the refrigerator itself, and any surrounding cabinets from potential damage. If your fridge is having issues opening or staying closed, check the hinges for any damage or cracking. To replace thi...Read mores bracket, simply remove the door off your refrigerator, unscrew and remove this bracket from the bottom of the door, and install the new one. This hinge bracket is an OEM replacement and is compatible with several different makes and models of refrigerator.
***NOTE: Ice maker does NOT come with the bail or shut off arm. You must order them separately if required. It does come complete with flat and round plug wiring harness, the mounting hardware, and the instructions. The harness can be reused. The ice maker will not fit refrigerators that have the ice auger mounted on the door.
This is a genuine replacement light bulb for a refrigerator. The inside of your refrigerator should illuminate when you open the door. If your fridge does not illuminate, you may need to replace this part. It is smaller than a standard light bulb, but has a standard size screw-in base. It measures about 3.75 inches in length.
This evaporator fan motor is located in the back of the freezer, and circulates air over the refrigerator coils. These coils will convert the heat into cool air, which is then circulated.
This temperature sensor is for refrigerators.
The temperature sensor senses the temperature inside the refrigerator and sends information to the electronic control.
Unplug the refrigerator and safely store any food that could deteriorate while the power is off before installing this part. Wear work gloves to protect your hands. The ...Read morethermistor itself, part WPW10383615, should test at these Ohms depending on temperature. It's recommended to test at room temperature and again in a glass of ice water to make sure it's sensing temperatures properly. So it should read around 3000 - 5000 Ohms at room temperature 7000 - 10000 Ohms at 0°C and 20000 Ohms at -15°C.
This track is a genuine OEM replacement part for your refrigerator. It is made of white plastic. The track supports the shelf within your fridge, and can be snapped in and out of place, which makes replacing this part very easy. Simply remove the shelf which is supported by the track, and replace your old track with the new one.
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Donna - For model number 10670212410
January 10, 2024
Timer
Hello Donna, thank you for contacting us. We have found that your model does not have any separate defrost timer. The control board, part number PS11753571, manages the functions of the refrigerator, such as cooling and defrost times. Glad to be of assistance!
I need the bulb for the freezer section of my Kenmore refrigerator/freezer.
Good Day Edward. Thank you for your question in regards to your unit (Model Number 10670212410). Based on our research the PartSelect Number for the part that is compatible with your unit is PS11775242. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
Hi Gene, thank you for contacting us. If the freezer fan is not running, it might be because of the ice buildup on the fan blades. Unplug the refrigerator and remove the evaporator fan cover. If there is a buildup, leave your refrigerator unplugged until the blades are free to spin. Ensure that the fan blades are not bent. If this does not help, then the problem is with the freezer fan motor, part number PS11740359. We hope this information is useful.
keep getting a thin layer of ice in the bottom of the freezer compartment then it drips down into the fridge compartment. I checked to see if the ice maker was leaking, but no. Looks like condensation on back wall of freezer and on the vent is dripping down and freezing on the bottom. I assume the anti-frost feature is thawing it out and dripping into the fridge area. If I don't remove the ice sheet in freezer every 3 to 4 days it will start to drip on the floor. Don't know what to look for. Please help, thanks.
Hi Mike, thank you for your inquiry. First, you may need to make sure the freezer door seals properly and warm air does not enter the freezer. If that is not causing the issue, then you may need to check the defrost thermostat, part number PS11754118, as it is the most likely cause of this issue and may need to be replaced. Glad to be of assistance!
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Ice Maker quit working, I could manually cycle unit but then the water would overflow when unit was re-filling.
596 of 639 peoplefound this instruction helpful.
Max from Green Castle, IN
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I backed out the 2 top screws about a quarter inch and then removed bottem screw with a quater inch nut driver. I then lifted Ice Maker clear of the two top screws and lowered it enough to unclip the power connection with a small screwdriver. The new Ice Maker was wired correctley for my refrigeator so all I had to do wea reconnect the
... Read morepower connection and mount new Ice Maker on the two top screws and install the bottem screw. It took e while for the new Ice Maker to start it's cycle but after it did, it worked GREAT. Part Select service was OUTSTANDING, ordered part one day and received the next. THANKS!!!!
Read less
Was this helpful?
Thank you for voting!
My refrigerator stopped cooling and the freezer section stopped freezing
441 of 556 peoplefound this instruction helpful.
garth from forest lake, MN
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I knew the chances of all the freon leaking out was unlikely so I looked at the wiring to the compressor and there was a capacitor and a starter/overload so i figured I would start there. I went on line and found the parts at this site and they were less than the minimum service call charge for a service tech so I figured what the heck le
... Read moret's give her a shot so I did give it a shot. I ordered the parts and they were there in less time than a service tech could come out and i installed the parts and guess what for 90.00 in parts and 15 minutes in time I repaired my refrigerator. Thanks guys, It took less time to order the parts than it did to make the repair so thanks, your website rocks and is very well designed so my hat is off to you guys!
Read less
Was this helpful?
Thank you for voting!
No Ice in the Ice Maker
201 of 237 peoplefound this instruction helpful.
Chris from Duluth, GA
Really Easy
Less than 15 mins
Socket set
I am NOT a handyman, and my family laughed at me when I said I was going to fix the ice maker all by myself. I ordered a replacement ice maker. When it arrived, I opened the box and read the instructions. It seemed easy. I removed the old ice maker, with a socket set. I then took off the shut off lever from the old one and placed it
... Read moreon the new one, since the new one didn't come with it. I then put the new one in place. All the parts fit perfectly. The ice machine was making ice within an hour. My family was amazed... and I got the last laugh!
My Orders
