My Orders
1053 - Overview
Models starting with 1053
Click on the best match to narrow your results.
Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".
Search filter:
Clear Filter
Your search term must have 3 or more characters.
$10.95
In Stock
Range Hex Nut
Part #WP112432
10-32 hex - Sold Individually - Appliance originally takes 3 of this item.
$19.95
Special Order
Gasket-Cylinder Head
Part #272314
$8.95
In Stock
18oz 30w 4 Cycle Oil
Part #100005
This bottle of oil can be used in over 150 different types of machinery. It is most commonly used for pressure washers and generators from manufacturers such as Briggs and Stratton and Troy-Bilt. This detergent oil is warranty approved and specially compounded for warm weather use. Please note: it is important to avoid over filling your engine with oil.
$10.95
Special Order
Gasket-Air Cleaner
Part #272512
$10.95
Special Order
Rope-starter
Part #280399S
This durable nylon starter rope is an authentic OEM supplied replacement part that is specially produced for use with Briggs and Stratton engines that are commonly installed on Toro lawn and garden equipment. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring. One starte...Read morer rope is included per order, please note the handle grip and other parts are all sold separately.
Read less
$5.95
In Stock
Key-flywheel
Part #222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Pliers to replace this item.
$15.95
Special Order
Link-mech Governor
Part #691829
$88.95
Special Order
Engine Recoil Starter Assembly
Part #497680
This authentic OEM starter assembly is designed for use with lawn and garden engines and is sourced directly from the original manufacturer to ensure quality and compatibility. The assembly includes a durable plastic shroud/housing, starter pulley, recoil spring, pull rope with grip, and the necessary hardware for installation. It functio...Read morens as the primary mechanism for manually cranking and starting the engine. To complete the replacement, you’ll need a wrench. Simply remove the four screws and nuts securing the old starter assembly, then install the new one using the included hardware. This item is sold as a complete individual assembly.
Read less
$30.95
Special Order
Shaft-Throttle
Part #493267
$11.95
In Stock
Kit-needle/seat
Part #398188
Genuine manufacturer approved carburetor needle valve for lawn and garden equipment engines. This item includes the seat. The needle valve opens and closes to control the flow of fuel into the carburetor. Make sure to disconnect the spark plug wire and drain all gasoline from the carburetor and fuel tank before starting a repair.
$8.95
Special Order
Insert-grip
Part #396892
The grip insert attaches to the starter rope. This is an OEM Briggs & Stratton, Toro, and Lawn Boy part directly sourced from the manufacturer for use in blowers, engines, generators, lawn mowers, pressure washers, and vacuums. Keep in mind that this part is sold individually. It is made out of plastic and will need to be replaced if it breaks.
$13.95
Special Order
Seal-oil
Part #399781S
This is an authentic replacement part manufactured for use with small engines. Seals can deteriorate overtime, and it is recommended to replace worn seals when servicing an engine. This seal is the lower seal in the engine's sump, the seal is sold individually.
Exact Part matches for your search term
No Longer Available
No Longer Available
No Longer Available
Common Symptoms of models starting with 1053
How this model fails, and the parts that fix it.
Will Not Start
Fixed by
these parts
these parts
Show All
Leaks water
Fixed by
these parts
these parts
Show All
Cannot pull starter cord out or engine will not turn over
Fixed by
these parts
these parts
Show All
Engine will not idle
Fixed by
these parts
these parts
Show All
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!
View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Replace carburetor
9 of 19 people
found this instruction helpful.
Loosened engine cover and moved out of the way
Removed air intake and filter
Loosened and disconnected gas line to carburetor
Unscrewed carburetor and disconnected from throttle arm
Reversed process using new carburetor, O-ring and gasket
Removed air intake and filter
Loosened and disconnected gas line to carburetor
Unscrewed carburetor and disconnected from throttle arm
Reversed process using new carburetor, O-ring and gasket
Other Parts Used:
Was this helpful?
Thank you for voting!
Mower body was die cast and in good condition. Engine was burning oil.
5 of 8 people
found this instruction helpful.
Removed engine, no specialty tools required. Honed the cylinder, and lapped the valves. Tip on compressing valve spring for reassembly; compress springs with you finger and tie them with 2 zip ties, cut the zip ties after installing the keepers. Repainted the mower deck and engine. It runs and looks like new. My Toro is a 1999 model .
Other Parts Used:
Was this helpful?
Thank you for voting!