048231013635 (ASSEEUS) LG Washer Dryer Combo - Overview

Diagrams for 048231013635

See every part. Know exactly what you need.

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Pulsator Cap – Part Number: 5006EA3009B
$45.05
In Stock
Pulsator Cap
★★★★★
★★★★★
(1)
Part #5006EA3009B
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a wash cycle. It is round in shape, and approximately 3 inches in diameter.
Washer Water Inlet Valve – Part Number: AJU75152601
$125.28
In Stock
Washer Water Inlet Valve
★★★★★
★★★★★
(4)
Part #AJU75152601
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stopping in the middle of a cycle, you may need to replace the water inlet valve. Be sure to disconnect the power and water supply before you begin this repair.
Pulsator Assembly – Part Number: AGZ72909711
$184.45
In Stock
Pulsator Assembly
★★★★★
★★★★★
(8)
Part #AGZ72909711
This is a pulsator assembly, also known as an agitator, for your washing machine. This pulsator sits at the bottom of your washer and is what is used as the main driving force to wash your clothes. If the pulsator in your washer is broken, it will need replacing immediately to continue to wash and clean your clothes evenly. The cap that sits in the center of this part is sold separately.
Washer Drain Pump Assembly – Part Number: 5859EA1004P
$215.53
In Stock
Washer Drain Pump Assembly
★★★★★
★★★★★
(6)
Part #5859EA1004P
This drain pump is for washers. Drain pump removes water from the washer during the drain portion of the cycle. Unplug the washer before installing this part. Wear work gloves to protect your hands.
Washer drain Hose Assembly – Part Number: AEM73732901
$58.25
In Stock
Washer Switch Assembly sensor – Part Number: 6501EA1001R
$57.15
In Stock
Screw – Part Number: FAB30598601
$24.15
In Stock
Tub-to-Pump Hose – Part Number: AEM73213001
$60.45
In Stock
Coupling – Part Number: MCJ61861201
$50.55
In Stock
Coupling
Part #MCJ61861201
HINGE – Part Number: MEF62462101
$16.45
In Stock
SUSPENSION ASSEMBLY,SUSP – Part Number: AJK72989704
$159.17
In Stock
SUSPENSION ASSEMBLY,SUSP
Part #AJK72989704
There are four suspension rods included in this kit.
Motor Stator Bolt – Part Number: 4011FA4353B
$13.15
In Stock
Motor Stator Bolt
Part #4011FA4353B

Common Symptoms of the 048231013635

How this model fails, and the parts that fix it.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
It did not drain water, cycle stops at rinse+spin.
28 of 36 people found this instruction helpful.
  • Jesus from El Paso, TX
  • Very Easy
  • 15 - 30 mins
  • Socket set, Wrench set
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su pplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
Was this helpful?
Thank you for voting!
Water continued leaking into washer after the end of cycle through the water inlet valve.
14 of 19 people found this instruction helpful.
  • Flora from MIAMI, FL
  • Very Easy
  • 30 - 60 mins
  • Screw drivers, Wrench (Adjustable)
Did the repair Myself. Saved $ 400.00 in the process.
Was this helpful?
Thank you for voting!
Water overflow in washer basin
11 of 15 people found this instruction helpful.
  • Ed from LAKE WORTH, FL
  • Really Easy
  • 30 - 60 mins
  • Pliers, Screw drivers
I diagnosed by running a full wash. I watched it and when the water should have stopped it kept running. I unplugged the washer from the power and the water kept running. This told me the inlet valve was the issue and not an electronic issue. I stopped the water by closing the water valve manually. Replacing the inlet valve was very easy . Hardest part is moving the washer out of the laundry room. The videos online show very simple steps. Maybe 8 screws to remove and a couple of hoses and five electronic connectors. Take a photo of connectors before removing them to ensure you reconnect properly.
Was this helpful?
Thank you for voting!