020733-00 Briggs and Stratton Pressure Washer - Overview
Sections of the 020733-00
[Viewing 3 of 3]
Keep searches simple, eg. "belt" or "pump".
Seal-o Ring
PartSelect #: PS8936675
Manufacturer #: 270344S
This authentic OEM replacement part fits a variety of Toro and Briggs & Stratton engines. An O ring is used to retain pressure between rigid parts. Its flexible material allows it to create a tight se...
$5.95
In Stock
Sealant-liquid
PartSelect #: PS8816307
Manufacturer #: 100106
It is a genuine manufacturer-supplied item that is made for use with Briggs and Stratton engines that are commonly installed on a variety of lawn and garden equipment. This is a special liquid sealant...
$24.95
Special Order
Kit-retainer Clips
PartSelect #: PS8907531
Manufacturer #: 195964GS
This authentic manufacturer-supplied part is specially designed for use with Briggs and Stratton, Troy-Bilt and Snapper pressure washers. It is a special hardware that helps to secure components. This...
$8.95
Special Order
Nozzle, Soap
PartSelect #: PS8911521
Manufacturer #: 198841GS
This is an authentic replacement part manufactured for use with pressure washers. The nozzle is used to provide an even spray when using soap or a chemical cleaner. This black soap nozzle is available...
$20.95
Special Order
Water Inlet Kit
PartSelect #: PS8911835
Manufacturer #: 201496GS
This water inlet kit delivers a controlled supply of water into the appliance, supporting proper operation during use. Designed for dependable flow and secure connections, it is commonly replaced when...
$87.95
Special Order
Water Outlet Kit
PartSelect #: PS8911836
Manufacturer #: 201497GS
This is a genuine OEM sourced component which is specially designed for Craftsman pressure washers. It is an identical replacement for a missing or damaged outlet that was originally installed on a ne...
$53.95
Special Order
Key-flywheel
PartSelect #: PS8925657
Manufacturer #: 222698S
This is a Genuine OEM replacement part used on a variety of Lawn and Garden equipment. The key helps to secure Flywheel in place. This is a Metal Key and it is Sold Individually. You would need Plier...
$5.95
In Stock
Nozzle, Qc, White
PartSelect #: PS8906872
Manufacturer #: 195983AMGS
This is an authentic OEM replacement nozzle made to fit the pressure washers listed below. This is a standard sized quick connect nozzle with a forty (40) degree spray pattern. This nozzle can be used...
$20.95
Special Order
Common Symptoms of the 020733-00
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Blown Head Gasket
This was an OHV motor so in order to get to the head, you must remove the valve cover and remove the push rods. Remove all four head bolts in an even star pattern. Remove the old gasket and scrape all remaining gasket gunk. Put new gasket on and tighten head back on with an even star pattern. Slide push rods back in and adjust valves to .004 of an inch and put valve cover back on and start it up!
Parts Used:
-
Isaiah from CHAMBERSBURG, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers, Socket set
7 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Blown Head Gasket
Remove the top cover and pull cord assembly. Remove the muffler cover. Lift off the gas tank and disconnect from the air filter box. Remove the air filter box and carb from the head cover as a single unit. Remove the head cover. You can leave the valve cover in place. Remove old gasket material. Clean surfaces. Replace gasket. Reassemble. *if the valve stems come loose from their seats or rockers, remove the valve cover and reseat. Reassembly is the opposite of disassembly. Happy mowing.
Parts Used:
-
Michael from BOAZ, AL
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Socket set
3 of 3 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Recoil broke apart
Removed cover then it required removing the broken recoil assembly to replace it with new one. New recoil assembly fit perfectly.
Parts Used:
-
Dexter from MAULDIN, SC
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver, Screw drivers, Wrench set
1 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!