01775-0 Briggs and Stratton Generator - Overview
Sections of the 01775-0
[Viewing 1 of 1]
Keep searches simple, eg. "belt" or "pump".
Fuel Valve With Bushing
PartSelect #: PS8911051
Manufacturer #: 192980GS
This is a genuine replacement part sourced directly from the manufacturer. The valve fuel kit is commonly found in Craftsman pressure washers and generators. This part includes the valve made of hig...
$33.95
Special Order
Filter-oil
PartSelect #: PS8982169
Manufacturer #: 492932S
This short-style engine oil filter is designed to remove harmful contaminants from the oil while maintaining proper lubrication in pressure-lubricated small engines. Built with high-efficiency filtrat...
$20.95
In Stock
Filter-a/c Cartridge
PartSelect #: PS8962593
Manufacturer #: 394018S
This is an authentic manufacturer approved replacement air cleaner cartridge. It is specially made for use with Briggs and Stratton engines. Its purpose is to remove dust and other contaminants that c...
$41.95
In Stock
Grommet,tank
PartSelect #: PS9307985
Manufacturer #: 83465GS
This is an authentic OEM part from Briggs and Stratton and Snapper for use with Generators. The fuel tank mounting grommet forms a cushion between the fuel tank and the fuel tank mounting bolts. The m...
$6.95
Special Order
Outlet, 120/125v, 15/20a
PartSelect #: PS9294308
Manufacturer #: 68759GS
This item is available as an individual replacement part. The outlet is made out of metal and plastic. It may require a wrench during installation. This item will need to be replaced if it breaks. It ...
$47.95
Special Order
Filter-pre Cleaner
PartSelect #: PS9274331
Manufacturer #: 272490S
This is a manufacturer approved replacement part used on a variety of lawn and garden equipment engines. This filter adds a second layer of protection against airborne-dirt particle ingestion. This is...
$8.95
Special Order
Vibe Mount, With Washer
PartSelect #: PS9269044
Manufacturer #: 191413GS
It is a genuine item that is supplied directly from the original equipment manufacturer for use with Briggs and Stratton generators and pressure washers. The purpose of this component is to reduce the...
$11.95
Special Order
Breaker, Circuit, 20a
PartSelect #: PS9919917
Manufacturer #: 209872GS
This part is an original part from Briggs & Stratton and Snapper for use in generators and welders. The circuit breaker goes inside the control box and helps to control electricity flow. A screwdriver...
$18.95
Special Order
Charger, 120vac, 13vdc Output,
PartSelect #: PS16443765
Manufacturer #: 84002790
This battery charger is used with a variety of portable generators. It is supplied directly from original equipment manufacturer and it is sold individually. It is used to deliver power from an outlet...
$69.95
Special Order
Common Symptoms of the 01775-0
[Viewing 1 of 1]
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Dry rotted rubber
Put some dish soap on the rubber, push into the tank hole, slip 1x2 into the handle of the tank and over the new part and pry down pushing it into the hole. Took about 2 minutes.
Parts Used:
-
James from PICAYUNE, MS
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
7 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old valve dripped gas when opened on cold sub zero day
old valve easily pulled out with screwdriver and pliers
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
install difficult due to 40 degree cold temp and bushing didn't want to squeeze into fuel tank hole
install required lots of liquid soap on bushing, which popped into place by using upward prying pressure from 3"X24" plywood braced into under-shelf of gas tank
used same technique to insert valve upward into bushing
works great!
Parts Used:
-
Alan from RADFORD, VA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
4 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
major gas leak on my generator
popped out the old-----the bushing failed. replaced as per the included instructions
Parts Used:
-
John from LEES SUMMIT, MO
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers
9 of 25 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!