Jenn-Air Cooktop Switches

Jenn-Air Cooktop Infinite Switch Left Front

★★★★★

★★★★★

29 Reviews

This surface burner switch is an essential component for electric ranges, controlling the power and heat level of the left front burner. It regulates the temperature by cycling the burner on and off to maintain the selected heat setting. If the switch is faulty, the burner may not heat properly, may remain stuck at one temperature, or may fail to turn on at all. For installation, first, unplug the range or switch off the circuit breaker to prevent electrical hazards. The control panel must be accessed by removing the back panel or control knobs, depending on the range model. Once the old switch is detached from the wiring harness, the new switch can be installed by reconnecting the wires in the correct configuration and securing it in place. Always wear work gloves to protect your hands.

Jenn-Air Cooktop Burner Switch - Right Front

★★★★★

★★★★★

4 Reviews

This dual surface element control switch is a critical component in select electric stoves, ovens, and ranges, responsible for regulating heat output and powering the surface element. It enables users to turn the burner on and off and adjust the temperature for precise cooking control. Typically located behind the front control panel, the switch connects to the wiring harness and interfaces with the surface element. If the burner fails to heat properly, fluctuates in temperature, or remains on when turned off, replacing the control switch may resolve the issue. Installation involves disconnecting power at the circuit breaker or unplugging the appliance, removing the control panel, detaching the faulty switch, and securing the new one in place while reconnecting the wiring to match the original configuration. Once installed, restore power and test the burner to ensure proper operation.

Jenn-Air Cooktop Surface Burner Switch - 240v

★★★★★

★★★★★

11 Reviews

This surface burner switch, also known as an infinite switch, is a key electrical component that controls the heat output of your stovetop burners. When you turn the control knob, the switch adjusts the power level to the burner, allowing for precise temperature regulation during cooking. If your burner is not heating properly, overheating, or stuck at a fixed temperature, the switch may be faulty and should be replaced. This part is compatible with a variety of ranges, wall ovens, and cooktops, and is sold individually without additional hardware. Installation requires a screwdriver, pliers, and a wiring diagram. Be sure to disconnect the appliance from the power source before beginning. To replace, remove the control knobs and access the underside of the control panel, then disconnect the old switch and wiring before securing the new one in place.

Jenn-Air Cooktop Surface Unit Infinite Switch Kit

★★★★★

★★★★★

6 Reviews

This is a push-and-turn switch. This kit includes all necessary hardware to install the part. Switch comes with a D-shaped shaft.

Jenn-Air Cooktop Surface Burner Switch

★★★★★

★★★★★

5 Reviews

A burner that will not turn on or off may have a bad control switch. The switch sends 240-volt power to the element based on the knob setting. First inspect the burner, wire ends, socket, and control knob because these parts can cause the same problem. Match the updated switch to the complete range model, even if its shape or terminal layout has changed. Disconnect power at the breaker and confirm the circuit is dead. Take a clear photo of the old wires, follow the supplied instructions, and close every panel before restoring power.

Jenn-Air Cooktop Infinite Switch

★★★★★

★★★★★

13 Reviews

The surface element control switch adjusts the heat output of your stovetop burner. It has a double flat shaft and is nut-mounted for secure fitting. Ensure compatibility before ordering.

Jenn-Air Cooktop Infinite Switch - 6 Inch

★★★★★

★★★★★

1 Review

Having trouble with the heat control on your Whirlpool cooking range? This 6-Inch Infinite Switch Surface Element Control is made just for you. Crafted from top-drawer materials, this real OEM part is specifically built to last while promising the best control of your range's heat. When your range isn't giving you the heat control you need, meals can end up undercooked or burnt, and that's no fun. This is where this new control switch jumps in! With it, your cooking range will be back to serving up meals just how you like them'no more guesswork on heat levels. Before you begin, it's crucial that your range is unplugged, or that your home's circuit breaker is switched off'for your safety. You should also consider wearing protective gloves to protect your hands during installation. In just a few minutes, your range will be back in tip-top shape! This control switch is a true testament to Whirlpool's commitment to quality and enhancing your cooking experience. Remember, using genuine OEM parts for your repair ensures a perfect fit and optimal efficiency. So go right ahead, get your plenty-needed Whirlpool Infinite Switch Surface Element Control, and return your range to its best performance. Enjoy those perfectly cooked meals again!

Jenn-Air Cooktop Surface Element Switch

★★★★★

★★★★★

10 Reviews

This surface element switch controls how much heat an electric burner makes. It turns power on and off in cycles as the knob moves from low to high. A burner that stays on high, will not heat, or heats at the wrong level may have a bad switch. Before replacing it, inspect the burner, wire ends, control knob, and nearby parts. Confirm fit with the full appliance model, terminal layout, and 15-amp, 240-volt rating. Turn off the breaker and verify that power is off. Move each wire one at a time before testing.

Jenn-Air Cooktop Dual Surface Burner Switch Kit

★★★★★

★★★★★

10 Reviews

This switch is used to operate the dual surface burner.

Jenn-Air Cooktop Right Rear Burner Switch

★★★★★

★★★★★

1 Review