Troubleshooting
This part fixes the following symptoms:
No hot or cold water
This part works with the following products:
Washer Dryer Combo.
This part works with the following products:
Whirlpool, Maytag, Kenmore.
Part# W11103599 replaces these:
AP6237529, W10114118, W10913964, WPW10114118
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Gordon B - September 9, 2018
Verified Purchase
Excellent easy to contact
Part arrived replaced water temp control now working very nice representative on phone friendly and helpful
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 4.5 / 5.0, 1 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Washing machine wasn't making proper temp, no cold on rinse cycle
Disconnect power, remove the three screws above the control panel, pull control panel from top toward you(it will hinge downwards) unplug wire harness from old ATC box, pull section knob off old ATC box front shaft, depress small tab on side of old ATC box and rotate box a quarter turn to free box. Install new ATC box, at a quarter turn till it snaps in place, replace selection knob ( make sure flat end of knob is lined up to flat end of ATC shaft), plug back in wire harness, push control panel back up, re install the three screws, turn power back on. Notes: Part numbers may differ from original, as long is the part looks the same it should work. This is the only circuit board component in my machine, and the only part to fail thus far.
Other Parts Used:
-
Richard from NEW ORLEANS, LA
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver
4 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ed
July 4, 2023
I get hot water when I choose warm or cold. I switched the hoses and get hot water when choosing cold or warm, but i get cold when I choose hot
For model number YWET3300SQ0
Hi Ed, thank you for contacting us. We have researched the model and would suggest checking the temperature control switch, part number PS12074684. It controls the incoming water temperature. We hope this helps, good luck with the repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Ali
May 24, 2019
I get hot water when i select cold on a tempreature switch and with the rinse cycle i got hot water instead of cold water, i changed the connections of water hoses ( cold hose to hot water tap & hot water hose to a cold water tap ) and still have the same problem ( i get hot water when i select cold on the tempreature switch and also with rinse cycle) what could be the problem (which part should be replaced )
For model number YWET3300SQ2
Hello Ali, thank you for your question. We would recommend replacing the temperature switch as well as the water inlet valve. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Ali
May 23, 2019
I have a problem with the washing machine when i put the temperature switch on cold water i get hot water and when the cycle in rinse i get hot water in stead of cold water. That means i need to replace the temperature switch?
For model number ywet3300sq2
Hello Ali, thank you for inquiring. For this symptom you will want to replace either the Water Inlet Valve part PS11742193, the Water Temperature Switch part PS12074684, or the Timer part PS11748397. We hope this helps.
Was this helpful?
Thank you for voting!
- < Prev
- 1
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS12074684
Manufacturer Part Number: W11103599
Manufacturer Part Number: W11103599
Brand
Model Number
Description