TFU20F7BW0 Tappan Freezer - Instructions

Repair was very easy. Just a scrwdriver needed to install. Glad I save my broken handle as the new one did not come with screws or face plate.

Took interior panel off and uncliped yhe termination switch and cliped the new one on the coil and connected the two wires very simple. The defrost timer was located in the rear of the unit on the right side at the bottom. Removed the 2 screws holding the bracket unpluged the timer and removed the timer. The new timer allready had a bracket so just plug in and install the 2 screws. Pluged the unit in and worked great make sure that the freezer is unpluged before changing any part

We really didn t need to do a repair, we just ordered a freezer key that we didn t have. I must say the shipping was fast we received it the next day. It was worth the shipping charge. We will be ordering again. Great service.

The handle for the freezer arrived the next day. Most of the time repairs at home are alway a challenge. But the handle was placed where it belonged in about 5 minutes.It was the easiest repair we ever had and now we don't have problemes opening the freezer. Thanks so much.

inserted key and turned

pulled out freezer, went to floor,reached in next to compressor pulled off clip just like on the video.Pulled off old capacitator took off wire leads.Installed new one. Freezer runs great.Loaded it up with beef pork and venison. No problems.

I first noticed my ice cream getting soft. Then 2 days later the alarm went. I emptied the freezer, opened the panels and saw no frost. I saw that 99% of issues were resolved with a defrost timer and thermostat so I ordered those. I have to say the parts came quickly and they went in very easy. My freezer seems to be in the 1% category though. It's still not cooling even though I can measure the temperature at the front of the evaporator coil is cold but by the end of the coil it's almost room temperature. I think a repairman is called for.

Notice ice build up on the panel in front of the evaporator coil. Unplugged freezer and removed evaporator panel. Plugged unit back in and checked fan, coil "snap switch" and heater element, all seemed to check out good. Found defrost timer stuck in the freeze position, causing frost to accumulate over the evaporator. Manually rotated defrost timer to the 30min defrost cycle and system went into defrost. Ordered defrost timer and installed (part arrived in 3 days). Freezer works great again. Too bad I ended up throwing 400 dollars worth of meat away. the fix was very simple. Will definitely use PartSelect again. Thank you.

I watched the videos (they really help) and followed the steps. Everything went smooth with no surprises

backed out screws from old handle, install new hansel w/ same screws & screw cover. done

I used a pick to remove the lugs from the old starter. Clicked them right in the new one and it went to woking!!!

Upluged power pulled freezer out from wall removed the two screws that holds the defrost timer unpluged defrost timer pluged new timer in mounted new timer back with the two screws pluged freezer back in and job was complete. Freezer working fine.

Our repair was very easy, just unscrew the old handle and replace it with the new one. The repair job took about two minutes and now the door is as good as new.

Remove cover on handle, and unscrewed the old handle. Then reversed procedure

The sliding shelf side rail is held by three philips head screws that tighten into nut inserts. No amount of tightening would keep two of the three screws tight. I found that the nut inserts which are plastic and insert into the side of the freezer would pull loose, probably from years of overloading the sliding shelf basket. Ordered two nut inserts from PartSelect. 1. Remove three screws to remove shelf slide side rail. 2. Remove nut inserts to be replaced with needle nose pliers or reinsert screw a couple of turns and pull nut insert out with pliers. 3. Insert new nut inserts, position side rail, and tighten screws. Replace sliding shelf/basket.