SER341AS0 Westinghouse Dryer - Instructions

The disassembly was very easy and it appeared that this would be a very quick repair. But the removal of the old felt was difficult and once it was removed it took a lot of effort to remove the bits still stuck on. The tool of choice to remove the stuck on felt was a small torch. After that use a coarse sand paper to remove the remnants. Glue on the new felt and reinstall the front panel.

I disassembled the dryer using instructions from the following website for White Westinghouse (pictures really helped)
After removing the drum, I first noticed that the grouding ball was sitting on the bottom of the dryer (along with much lint). I then saw that the bracket for bearing support cup and the bearing support cup were both worn well past use. The bracket had been worn down about 1/4" to the SE with matching wear on the bearing support cup. There was a hole in the bottom of the bearing support cup (hence the grouding ball on the floor of dryer).
I installed the new idler pulley assembly and completely vacuumed out the dryer (I didn't know lint could get so stiff!). I installed the new parts from the kit once received (and the new belt bought previously) and the dryer works great. I'm so used to the obnoxious squealing that it seems odd to be so quiet.

The internet is a magnificent thing!

This is a stacked wash/dryer.
- unpluged washer/ dryer
- removed front panels under dryer drum area
- disconedted the wiring connection from washer to dryer
- removed front door panel
- disconnected and removed belt
- removed screws holding in drum
- removed drum
- replaced felt on the door (came with drum replacement kit)
- aligned and attached new drum
- replaced belt on drum
- aligned and installed door
- reconnected wiring connecting washer and dryer
- installed fron panels under dry door
- pluged in washer/dryer
Works like new

Followed your website repair guides and the great belt replacement video.

Other parts used were; front lower basket seal, dryer seal, and dryer drum belt.

Had no problems except for keeping the drum belt idler pulley tension spring in place. Used the rear access panel to solve this issue.

John H.
Palm Desert, CA

we simply screwed the new one in place

I followed the recommendation from William, from Ardmore, OK and Elvis, from Miami, FL for the repairs. Elvis had detailed instructions as well as William, so I just combined the two and I was able to repair my dryer in three hours time. My sincere thanks to partselect web site in posting the repairs on line and for everyones input. I will be back to use the web site again to troubleshoot my other appliances and order parts (great price, fast service for parts) and I will highly recommend this site to my friends.

Watched on-line video, then applied those steps.
1. Pop the front of the deck loose using putty knife to depress clips;
2. Disconnect wires from light and door switch;
(Before I disconnected wires from door switch and light, I made wiring sketches to make sure I reconnected in original manner.)
3. Remove lint filter mount screws and mount from bottom of door opening;
4. Cut drum belt with wire-cutters and removed it;
5. Remove drum support clip from top center of front panel;
6. Remove (1) screw from each side of dryer body that hold front to sidewalls, removed front panel;
7. Remove drum by lifting the rear out of the bearing, then moving it forward through the machine front;
[While I had the dryer disassembled, I thoroughly cleaned it of lint, dirt & metal filings. The metal filings were from the worn ball hitch and drum support bearing cup. I spent as much time cleaning it out as I did working on it.]
8. Stand drum on gallon paint bucket while removing ball hitch (Use a #2 drywall phillips apex to obtain sufficient seating & torque to remove and reinstall ball hitch screws at rear of drum.);
9. Have a second person hold the new ball hitch in position while starting screws, if necessary;
10. Use nut driver w/5/16" socket to remove bearing retainer & ground ball clip;
11. Install new bearing into retainer clip, insert attachment screws through the holes in both, stick grounding ball in depression on back of bearing as screws are fed through back panel;
12. Hold ground ball clip in place to start one screw, then the other & tighten with nut driver;
13. Start drum belt on motor shaft and position against tensioner pulley;
14. Feed drum through front of machine and loop belt over rear of drum;
15. Slide belt forward on drum as drum moves to rear to keep it aligned with position of tension pulley;
16. Lift rear of drum to place ball hitch on top of bearing, then press down to seat it into bearing;
17. Turn drum to ensure belt alignment, then re-accomplish steps 6 thru 1.

The new motor from parts select was not correct. The new motor is a bolt on. The original motor was a press on. Had to return at a cost of 42.00 dollars. Had to buy a new dryer.

much as described earler,
1. Removed 2 screws on back at the top and 2 on the chrome vent to access the belt and pulley.
2. Disconnected spring from pulley assembly and removed belt from pulley and motor.
3. Removed top of dryer.
4. Removed control panel.
5. Removed screws from inside dryer tumbler (all of them)
6. Removed bottom kick plate.
7. Removed 2 screws from inside panel (near tumbler) and 2 screws from bottom of front panel. Removed front panel.
8. Removed tumbler housing.
9. Removed heating element cover.
10. Removed heating element pan. (wires first)
11. Removed "bearing" by lifing it up (snaps in)
12. Cleaned and regreased "bearing"
Assembled in reverse order.

When it comes to repairs the only thing that I can fix are sandwiches. To say that I am a handy man is usually followed by snickers from my wife and friends... However, I was able to completley take apart my dryer, replace the heating pan and coils, put it back together and it works all by myself (my wife was standing behind me with a fire estinguisher when I plugged it in for the 1st time). I took the advice of some of the post I saw on this sight and took some before shots with my camera phone and marked the wires with tape so I knew where to return them and was able to get it all done. I was suprised at how easy it was to do and how simple a dryer really is on the inside. Ordering the part and doing it myself saved me a couple of hundred dollars easy.... this was the way to go!

There are only three screws holding the drum in. However, to get it out I had to remove the front panels, and the top of the dryer part of the washer-dryer combo. The drum came out easily, but getting the new one in was pretty hard. I had to guess how the drive belt was routed around the motor pulley and idler pulley, since I couldn't see it until I'd removed the drum. Since the new drum wasn't exactly like the old one, I had to remove the glide strip from the front panel to get it to fit. At present, the unit is not completely reassembled, so I can't say I've been entirely successful. Tomorrow, I will put it back together, cross my fingers, and switch it on. Wish me luck!

Followup: The dryer part of this washer-dryer combo is back online. At first, the dryer made a squealing noise, but eventually quieted down. At present, the drum replacement seems to be just fine. It cost about $215, and, except for a few cuts due to sharp-edged metal, a dropped clip that disappeared into the depths of the bottom of the washer, it is actually REPAIRED. I could have used more specific help, but, all in all, it has been pretty easy, and pretty effective.

I push the new knob onto the post that fit the knob

Simply popped it back into place, careful not to break the new handle.

I googled and found parts select, listed model make and found parts diagram, found suspected parts from trouble shooting blog. I read repair stories, people who performed identical repairs, followed their lead, made notes ordered parts and
easily repaired my dryer for a fraction of the cost of replacing dryer.

After unplugging the dryer, disconnecting it from the vent, and moving into an open work area, I popped the top open with the blade of a screwdriver, disconnected the two wires that connect to the door switch, then lifted the front panel (with the door) up and away from the drum. Next, I lifted the drum out of the worn rear bearing assembly and lowered it into the dryer in order to release tension on the belt. I then removed the entire drum by carrying it forward and out of the way. I then removed the old bearing assembly, which was loose and covered with metal dust. After cleaning the area with a dry cloth to remove the old grease and metal dust, and vacuuming all the lint off *everything*, I installed the new bearing assembly with a 5/16" nut driver, being careful to position the provided ball-bearing between the plastic bearing assembly and the outer clip. The little ball-bearing is very important, as it is the drum's only path to ground, and prevents the build up of static electricity as the drums spins. I then filled the new bearing assembly with the provided grease. Everything is easy up to this point, but the difficult part for me was removing the old hub from the drum and re-attaching the new one. It is held on by three screws and they become seated very tightly. After loosening them and removing the old hub from the drum, attaching the new one prvoed difficult as well, as the screw-holes in the new hub are not threaded to fit the screws. The screws muct be forced to cut a thread as you install them, which requires a great deal of force. After installing the new hub and putting the new belt (pruchased separately) around the drum, the next step is to reinstall the drum by lifting it in through the front of the dryer and positioning the new hub over the new bearing assembly and pressing it down into place. It will gently "snap" into place as it seats. Then, on the back side of the dryer, I removed the vent panel by removing the two screws that hold it in place and positioned the new drive belt (loosely dangling around the drum) over the motor's drive wheel and behind the sring-tensioned idle arm. Then it is a simply matter to reinstall the front panel by genly lifting the drum and sliding the door opening inside it, then reseating all the little clips that hold the front panel in place. I then pressed the top back into place, reconnected the vent hose, plugged it back in and checked for operation. My fifteen year-old dryer now works like new!