GTWP1800D0WW General Electric Washer - Instructions

simply pulled the old one off with the broken clip and pushed the new one on. This is the third or fourth time we have used Parts Select and have always gotten the best service and best price.

replaced them & working fine now....

With screwdriver, I removed screws holding old hose in place. Attached new hose and screwed into place.

It tooke some time to figure out where the water was leaking. It was from a small hole at the lateral side of the upper third of the drain inlet tube. Removing the hose was easy. Attaching it to the tub with a hose clamp was easy, but attaching the lower end to the pump motor was quite difficult because the spring clamp that had come with the washer was difficult to manipulate. I had to replace it with a band hose clamp.

By the way, the hole in the hose had been caused by rubbing the hose against the drain pipe from the motor to the sink.

Unplug the washing machine. There are electrical components that can injure or kill you. Using a screw driver inserted just below the lid of the washer in the front, there are two (2) spring clips that you push on to release. Then the front of the washer tilts down and you remove it and set aside.
On the bottom right you will see the flexible, convoluted rubber hose connecting from the pump to the washer tub. Two (2) clamps hold the hose on. Remove the two clamps, install the new hose and re-install the clamps. Re-install the front panel and push into place, allowing clips to lock into the front panel.

I just removed the clip and took off the old knob. I than put the new one on and replaced the clip.

I replaced the hose between the tub and the pump. The only difficulty came with the accessibility of the problem area. I just pulled off the front panel of the machine and used a screwdriver and pliers to loosen the attachments and put the new hose in place.

Removed three nut screws and raised the control panel forward twisted the old switch off removed one wire at a time and put it on the new switch. I did this so the wires would be where they should. After I put the new switch on I replaced the three nut screws I plugged the washer in set it on cold water and it worked like it should.

I pulled on the bottom edges of the agitator, like the video said, until my fingers were numb. Finally, after I got aggravated, I beat the old agitator into a hundred pieces with a hammer and chisel. Then I slid the new agitator into place and gently tapped on the top of it. It snapped into place and has worked like a new one every since.

I followed the video from the website to install the lid switch. Worked like a charm. Great instructions. You do need to supply your own butt splice connectors .

The repair went just like the video! Easier than I would've hoped.

Followed video on You tube that showed step by step how to compete repair.
The machine used in video was brand new and there was no corrosion on any parts so disassembly was much easier in video than on 9 year old machine.
Also reinstalling drive belt was a little tedious but overall job very straightforward and resulted in positive improvements in performance and greatly reduced noise levels.

I paid over $100 several years ago to have this same repair done by an appliance repairman. I did it myself this time for less than $20. Definitely watch the installation video before you start. Remove agitator by pulling it up by its bottom flange (protect your face in case it pops off suddenly). Remove bolt holding agitator coupling onto the transmission shaft. Pull up on old coupling and remove it. Clean grooves on transmission shaft and then install new coupling over the shaft. Reinstall old bolt and the agitator following video instructions on lining up agitator on the coupling. Note: Standard Fedex Smartpost shipping took 6 days to go from Louisville, Kentucky to western North Carolina. If you're in a hurry it's worth it to pay for expedited shipping. Lots of dirty laundry piles up in a week!

This was one easy job and saved me money by doing it myself, First I unplugged the washer for safety, then I removed the Agitator by grabbing the base of the agitator with both hands and pulling up I set the agitator a side and removed the one bolt holding the agitator coupling in place. the replacement coupling was a little tight when I replaced it due to it being new, (make sure the coupling is fully seated before installing the bolt) reinstalled the agitator plugged the washer back in and tested repair worked flawlessly thanks partselect

Pulled the agitator off by hand. Loosened the screw on top of the coupling and pulled old coupling off by hand. Replaced part with new coupling and socketed it in place. Replaced agitator by-hand by simply pushing it down on top of coupling making sure the plastic teeth aligned.