AUF170KW Amana Freezer - Instructions

disconnected el. power to fridge. pried out broken switch with small screwdriner and pulled out w/water pump pliers. installed new switch and pressed into opening.

I had ordered some other parts for something entirely different off your website and service was great. So after almost ten years of a dark refrigerator, because of a defective switch, I decided to see if you had the part to fix it... You did and the part got here in 3 days. I had a working light switch and all the light in the world where my husband needed it most (in the fridge). It took me at the most ten minutes to replace the part. All is well now and I have a happy husband who can find the leftovers just fine. Thanks for your great service!

My Amana washing machine burned up a second belt in about three weeks. Prior to that, the spin cycle was very loud. Online research revealed the problem was most likely the hub bearing. I ordered a new bearing, belt and hub and seal kit. The repair is a difficult one as the parts have been on the tranmission shaft many years with the mounting corrosion and mineral build up. I was able to pull the agitator off with no problem. The drive bell would have been easier to pull had I used a gear puller but did not own one. I use two crow bars to lift it off the shaft and I knew I'd be replacing it anyway so was not concerned about damaging it although I didn't. The most difficult part to remove was the large hex nut. I didn't want to purchase the tool to remove it so I used an open end adjustable wrench adn a hammer to remove it. However it took many hours of soaking the nut in sprayed on WD-40 to loosen it. For a while I thought it wasn't going to budge. Oh and btw, the nut comes off counterclockwise on this model. This is important. Other makes of washers have left handed threads, requiring clockwise removal, but this one does not. The hub assembly was pulled using the crow bar method. Again, it was going to be replaced anyway. The lint filter was cleaned and reused. The remainder of the dissassembly went OK using the directions in the repair manual. http://www.scribd.com/doc/8677902/Amana-Top-Load-Washer-Service-Manual. Reassembly went fine using the repair manual accept that the new drive bell was much more difficult to drive onto the shaft than I thought it would be. I eventually got it on using my shop vac rigid tube to go around it and hammering on a block of wood placed on top of it. I also used this shop vac tube to seat the seal that goes on the shaft just before the drive bell. It was the perfect tool for it as I wasn't going to purchase the special tool suggested in the repair manual. I'd already purchased $185 in parts. The kits come with grease but not the anti seizure compound or the industrial sealant needed. The anti seisure compound can be purchased from an auto parts store. It's not expensive. The industrial sealant is expensive. After researching what it was and why it was needed, I took a chance on silicone sealant. I'm not suggesting it is a good substitute but my washer has not leaked after 5 loads. Plus the sealant is really a backup to the main seal that goes on the transmission shaft before the hub assembly. But I'm pleased overall with the parts and accompanying directions and the washer is working great, spinning quietly. This is not an easy repair. It takes patience and a place to work on it. Frankly, with other things to do as well as go to work, it took me four days to complete, mostly due to the difficulty in removing the large hex nut. It might be worth investing in the removal tool if you're unsuccessful using home tools. Good luck.

We tried repairing with a new switch which was very easy to install but it didn't fix the problem.

This is an easy fix, simply remove and replace. What I was impressed with is that a how to video was provided along with my part. I wish all manufactures would offer this, the video was easy to understand and you had a good view of the operation. Thanks, a job well done.

I had the best luck using pliers to remove the hex top screws. Once the screws were removed I unplugged the old defrost timer and plugged in the new one. Replaced the screws and the freezer worked when plugged in.

Viewed the viedo - it showed what to do

followed the video as instructed. Saved two repairman calls, one to find the problem, one to install. Net savings was about $130.00

1)pry out the old/defective light rocker switch with a screw driver (flat head) and pull out the cables 2)unplug two connectors at the end of light rocker switch 3) connect new light rocker into two connectors 4)push the wires inside and put back new light rocker switch

I did exactly as the video showed. I popped out the old switch, disconnected the two terminals, connected the new switch and put it back. The light now works! The refrigerator is over 25 years old and the switch works! What a great website this is. Couldn't of done the job without Partselect's help.

put the new gasket in a tub of hot water. remove door and lay on flat surface, remove old gasket and pull hot gasket from tub, dry and install, the hot water helps remove the wringles from shipping.

I unplugged and defrosted the freezer ( good excuse to give it a good cleaning). I then removed the hex screws from the door under the gasket. Because this attaches the door panel to the freezer, it is helpful to have two people for this task if you have a full size upright freezer. We then removed the panel, cleaned the door, and fitted the new gasket in place. If your gasket has kinks in it, either throw it in the dryer on low for a few minutes or use a hair dryer to smooth them out. We then added a few screws around the center point of each side to hold the gasket in place, secured the corners, and replaced the remainder of the screws. We used a small cordless drill. The gasket will be hard at first, so I duct taped the freezer door shut with a few pieces of tape and turned the unit back on. A repair guy was going to charge me $350.00 for the job, but I did it for free with the cost of the gasket. This site is the least expensive place I found anywhere, and shipped very quickly!

Just put the two screw back in that i had removed.