ADB1500AWB46 Amana Dishwasher - Instructions

Removed two screws at the top of the base washer. Three screws removed down both sides of the base washer. Lifted washer out enough to see the cable and spring connections. Removed cable and replaced with new and re-connected. Slid washer back into position and installed screws.

I watched a couple of videos on Youtube, and for once it was actually easier than anticipated. Unplug unit. Remove door screws. Separate inner door from outer door. Remove connector from dispenser (needed flat blade screwdriver to pry it at first.) Remove six screws holder dispenser in. Removed old dispenser, inserted new one, tightened six screws, re-connected wires, attached inner door to outer door, and was done in literally less than 10 minutes. Note: I was using a battery powered screw driver to remove the screws, so that's one reason why it went so fast.

It was very easy to replace the broken door spring, I received the new spring from PartsDirect in two days. I removed the 6 screws holding the dishwasher to the counter and pulled it out from the counter about a foot, no need to disconnect the power and water. I simply replaced the broken spring using the right side spring as a guide. I pushed the dishwasher back in and reinstalled the screws. I completed this repair in less than 20 minutes.

No repair needed, just inserted the new dishrack. My only complaint is the lack of upright tongs in half of the rear section of the rack. This limits the number of dishes that can be stored. My original rack had tongs in all areas which better suited my needs. If there is a replacement that better suits my needs I would like an exchange.

easy repair. The foam has to go over some wires but if you stretch it alittle as you place it all goes well

Remove screws holding the inside of the door. Set lid aside. Pull out the old foam insulation. Clean the area. Replace with new foam insulation. Put door back together.

Pull dishwasher about 1/2 out of cabinet. Remembered to turn off power just in time. Removed electrical leads. Hand removed nuts retaining the heating element. Installed new element - hand tightened nuts.

Removed the rack from the dishwasher.
Took off the adjuster from the rack using the allen wrench.
Replaced the new.

Perfect

A really easy and simple repair that required no tools. The parts were delivered within a matter of days. Completely satisfied with transaction and results.

I have done two repairs, and both times PartSelect.com came to the rescue! The first repair was a few years ago when the dishwasher would run but nothing got wet. It made all the right noises except the sound of water being thrown around, because no water was being pumped! This resulted from a cheap plastic "chopper" assembly that stripped and wouldn't drive the impeller. PartSelect sold me a solid metal replacement part for under $10 and that fixed the problem for several years.

Recently, we had a different problem where the dishwasher completely haulted and the wash motor wouldn't run. This was caused by a faulty impeller, another cheap plastic part. The wash impeller fragmented around the drive shaft to where it sat uneven and thus created too much resistance for the motor to drive it. I removed the impeller, superglued the plastic parts together so that I could then wrap them in copper wire (about 1mm diameter), and then I hot-glued over the copper wrapping to secure the entire thing and to help keep water out of it. I did this so that we could wash dishes while we waited for the new impeller. Well the new impeller came several days early and so far I have just been too lazy to go remove the makeshift part. I figure it will fail sooner or later and then I will install my new part which should give me at least 9 more years of trouble free washing!

Remove screws holding the existing white panel. Once that panel was loose, there are several screws internally that have to be taken out in order to fully remove the panel. The new panel is then installed by putting it in place and reinserting the screws. It is an easy"fix" to change the DW to match other stainless steel appliances. You do need to be careful to make sure the door springs stay attached.

Docking station just pops out, you grab the right side and pop it off. Replace by placing the left side in place and then push the right side until it snaps in place. VERY easy.

The gaskets were worn out and that was allowing a lot of water to escape, not enough pressure to clean the dishes.

The old docking station seals were getting very soft. To put a band aid on the wound until the new docking station got here I put a sleve on the washer bar feeder tube. This made an improvement. The docking station was removed using a screw driver to unsnap the station. Then all I had to do was snap the new one in. Be care ful not to pull on the piece the docking station is snapped on to. There are metal clips behind there that hold that water delivery tube on to the back of the dishwasher. Those clips are twisted on and can be striped off easily by pulling strait towards you. If that happens you must secure the clips using self tapping screws and a water proof sealent.

I removed the shelves out of the dishwasher unsnapped the old parts and snapped in the new! Replaces the shelves and it is washing like a new machine! Thanks!

No repairs needed other than opening the box and placing into dishwasher.