ACS4250AC (PACS4250AC) Amana Range - Instructions

I went online to learn what F-3 meant and it said temp sensor malfunction. I ordered the part - it looked the same so I repaced the old one and then the plugs were different. I cut the plug off the old sensor and cobbled together a connection. I powered up the stove and the burners were ok, but the oven appeared dead. about an hour later the alarm went off and it displayed F-1. I figured I needed to order another part, but hit Oven cancel and the display lighted up. I set the clock, heated to 400 and made a tray of cornbread. It seems to work ok, but I need to make a better arrangement. perhaps cut the new part connector off and splice the old connector. I don't like having electrical tape so close to the oven - it will probably melt with much usage. It is working - for now!

Unplug power cord, remove wires from block. take 2 screws out. replace with new block about 15 mins. Done

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old hinges and installing the new ones.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

ordered new broiler pan

I pulled down the wire around the glass cover. . . Released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

very easy

Ordered and received the terminal block. Installed it along with a new 220V power cord and the appropriate insulator . Ensured the terminals were tight with a nut driver. Reinstalled cover. Then, using the control panel, I did a function check on all the heating elements, clock, oven light, to satisfy all operational requirements. All checked good! And, I was relieved that the control panel had not been shorted out as the terminal block was due to a loose connection. Easy fix.

Screwed in light bulb and glass protector

just needed clearner for the top of my glass top, the operator was very helpful I received my clearniner in 7 days thank you

r & r hinge. very poor pivot pin which leads to frequent replacement of hinge assembly, cheaply made, weak spot is hinge pin pivot rivet.

Insert one end of the railing into the slot in the back of the stove. Align the front end of the railing with the hole at the front of the stove. Align the roller with the hole. Secure the front end of the railing, roller ,and hole with the shoulder bolt using a 10mm wrench. Tighten just enough but don't over tighten.

turn the power off first, remove knobs, removed burners,disconnected wire from igniter,raise the top of the stove,re rmoved wire from the door lock removed two screws remove the door lock itself, then put all back on in same order as I remove. Main thing to remember is to writeyour colors of the wire down so you know where to replace them.

The repair was very easy. It took me less than ten minutes. There were only five screws including two to hold heat element that I have to unscrew and transferred the old clip the screw onto new heat element.

Move stove away from wall to allow working on back of stove. Unplug stove. Remove metal cover from top rear of stove. Pull control knob off of control (front of stove) Remove 2 screws holding infinite control in place (front of stove) Replacement control not identical to original control, having more terminal lugs and different physical arrangement. I used the terminal letters as a guide for placement of wires. The letters were not exactly the same, but close enough. Re-attach control to stove with 2 screws. Re-attach back metal panel to stove. Shaft on replacement control is smaller diameter and different shape from original, so I removed ribs from inside of control knob hole and then squirted a small amount of hot glue into the hole. Smearing a small amount of cooking oil onto shaft of replacent control I then slid the control knob onto the control shaft, holding it in place until the glue cooled and set. Plug stove back in, and return stove to its position next to the wall.