66513154K700 Kenmore Dishwasher - Instructions

Removed new from box and installed rollers as instructed that's all there was , very easy.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

After pulling the dishwasher out from under the cabinet, I found it underneath near the back right side. I disconnected the old thermostat, unscrewed the clamp holding it into place, put the new thermostat in, screwed it back in and replaced the two plugs. Then I pushed the dishwasher back into place, and it initially didn't work until I found an online forum that was able to identify the reset command for my dishwasher (for the WDT710PAYM4, press any three buttons in a sequence of 1 2 3 1 2 3 1 2 3. After completing that all the lights lit up, and I shut the door leaving it for half an hour) Once the reset finished, the heated dry worked like it was suppose to.

A Mouse friend had seen fit to chew through the original drain line. I used my Model Number, and was able to order the correct part . It arrived the next day. The job itself is fairly straight forward. You will need to access the rear of the machine. This may include shutting off, and disconnecting the water supply line. (Adjustable wrench). Mine is under the sink, on the "Hot" side. You may also need to un-plug the unit. (recommended) . A pair of (Pliers) will be needed for the spring clamp.

1.Check the lines for any obstruction. Gunk can easily build up. I have used the dishwasher for approx. 10 years. I do rinse/scrap dishes prior to loading.
2. Drain all remaining water.
3. Unplug the dishwasher.
4. Grab a towel and proper screw driver. Unscrew the bottom protective plate. Remove the insulation plate.
5. The drain pump is located to the bottom left. Have your towel under it. Unplug it gently. Turn counter clockwise to remove.
6. Install the new drain pump (reverse order)
7. Return the insulation plate. Screw back the bottom protective plate.
8. Plug in

Since I had manual from initial installation I knew code meant heater was malfunctioning. Went to Sears, Lowes..no parts to repair. Instructed to go to appliance repair shop, closed of course...ordered online instead here and received in 2 days. Repair took 20 minutes. Super easy! Do not attempt to use adjustable wrench to tighten, use socket set as plastic electrode casings will be compromised. Takes some tork. Probably saved $100-$150 repair call. Wife was pleased. I was suprised how easy.

I watched the video identifying the part and the procedure to make sure I could handle this. The phone attendant was also very helpful in making sure I ordered the correct part,which arrived in one day (amazingly). Everything was clearly described in the instructions and if you have done electrical work this would be relatively easy. You will need a specific screw driver bit to open the control panel but everything else is straightforward, just follow the instructions. Works perfectly now (I needed a new control panel about a year ago and Kenmore charged me $229 but it was just over a year since then....) PartSelect is a great service!

I removed the old seal and carefully cleaned the track into which the seal was fixed. No tools other than some ordinary cleaning liquid, cloth and small wooden piece to swab out the track. Easy and quick. As a note here, I first used the incorrect schematic for the unit and ordered the wrong seal. However after receiving the wrong part, I made the correction and reordered. I did this over the phone as I needed instructions to return the part. The person taking my order and answering my questions was very helpful and I want to take this opportunity to thank her.

The old tine row came out easily and the new one was easy to pop into place. I was pleased that it was so easy to order a replacement part.

I am a 61 year old woman and it took me a total of 2 min. max. Popped it into place and pushed in button that holds it..Taa Daa...perfect!

Unplug dishwasher and slide it out from under cabinet. Remove old broken link (a heavy string between two plastic parts) and replace with new one. Slide dishwasher back and plug it in. Very easy and no tools required.

Tried to clean old part and it did not work. Ordered the new part on Saturday and received it on Tuesday. Removed the old part and installed the new one. Ran the machine and it worked great. A big savings on not having to buy a new machine!!

Removed old part and replaced with new part

Removed the old tines by pushing out the clips on the end and then installed the new tines and applied clips - took 10 minutes worked slick and the washer basket looks to be brand.

Removed old rack and and removed old rollers and installed old rollers on new rack as they work better than the new rollers sent with new rack