6530A REV A Norge Washer - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Grinding noise, then motor shut off.
Disassembly
- Took the back bottom plate off.
- Removed hoses.
- Removed pump with pulley (3 nut screws)
- Removed belt
Installed new parts
- Installed pump with pulley (3 screws)
- Installed belt by placing on 2 small pulleys, then turning onto the large pulley (used a screwdriver to help align over pulley for leverage).
- Replaced hoses
- Replaced back plate.
- Took the back bottom plate off.
- Removed hoses.
- Removed pump with pulley (3 nut screws)
- Removed belt
Installed new parts
- Installed pump with pulley (3 screws)
- Installed belt by placing on 2 small pulleys, then turning onto the large pulley (used a screwdriver to help align over pulley for leverage).
- Replaced hoses
- Replaced back plate.
Parts Used:
-
Joseph from Phoenixville, PA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers, Socket set
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
terrible grinding noise
For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my
Parts Used:
-
ALVA K from chippewa falls, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
9 of 10 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
washer would not spin.
tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!
Parts Used:
-
Robert from South Gibson, PA
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
10 of 13 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Loud squeal when spin cycle finished, white powder under washer
Read DIY review from William, Middleton, OH on 01-15-08. Tip on how to relieve spring pressure on brake assembly worked like a dream (3ea 10-24X2 bolts/machine screws). Replaced brake and machine works like new and was an inexpensive fix. Once the shell/housing is off the machine, tub can be turned upside down and the base doesn't need to be removed. White powder under machine was a plastic wear ring that tells you when your brake rotor needs to be changed. Brake rotor still had lining but was much thinner than replacement part. Note* Use putty knife to push in clips on front to release the top lid section.
Parts Used:
-
Kevin from Pooler, GA
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Wrench set
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer made a loud noise during spin-eventually stopped spinning
I was able to get the belt off easily but the belt was fine. I changed the snubber easily also. But that wasn't the problem. I went through all the parts that are easy enough to change without a mechanic but turned out it was something inside the innerbasket and we had to junk the washer and it was only 4 yrs old.
Parts Used:
-
Christopher from Haverhill, MA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
-
Tools:Socket set
8 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Fill water would not reliably shut off.
Open the top of the washing machine by using a putty knife to release the latches at the right and left side. Prop up the top so it doesn't fall while working.
Remove the inlet hoses and put in bucket to catch water.
Remove the two screws that hold the inlet valve in place.
Remove the wires from the inlet valve. (One of the spade connectors one wire broke and I had to replace it.) I used needle nose pliers to pull the spade connectors off.
Remove the outlet hose.
Throw out old valve assembly.
Attach hose to new valve assembly. (My old valve assy outlet was slightly smaller in diameter than the new valve, but I was able to get the outlet hose to stretch enough to fit--couldn't use old spring clamp though, but new valve came with a hose clamp--worked fine.)
Attach wires same way as they cam off old valve.
Position and use the two screws to screw assy back into back of washing machine. (The screws had to tap the holes on the valve, so start out a little hard.)
Reattach the inlet hoses and check for leaks.
I also ran both the hot and cold in a cycle and the reraised the top to check for any leaks internal to the machine.
Pus the top back down to engage its fastening clips.
Job done.
My washing machine is 23 years old.
Remove the inlet hoses and put in bucket to catch water.
Remove the two screws that hold the inlet valve in place.
Remove the wires from the inlet valve. (One of the spade connectors one wire broke and I had to replace it.) I used needle nose pliers to pull the spade connectors off.
Remove the outlet hose.
Throw out old valve assembly.
Attach hose to new valve assembly. (My old valve assy outlet was slightly smaller in diameter than the new valve, but I was able to get the outlet hose to stretch enough to fit--couldn't use old spring clamp though, but new valve came with a hose clamp--worked fine.)
Attach wires same way as they cam off old valve.
Position and use the two screws to screw assy back into back of washing machine. (The screws had to tap the holes on the valve, so start out a little hard.)
Reattach the inlet hoses and check for leaks.
I also ran both the hot and cold in a cycle and the reraised the top to check for any leaks internal to the machine.
Pus the top back down to engage its fastening clips.
Job done.
My washing machine is 23 years old.
Parts Used:
-
GARD from FAIRFAX STATION, VA
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Socket set
8 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Parts Used:
-
Howard from Boynton Beach, FL
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
22 of 52 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Oil leak from lower lip seal
I didn’t have special tool for brake but punch and hammer worked. Seal was easy to replace. Several videos online to show you how. It wasn’t worth it to tear apart the transmission and buy more parts/seals (if they were even available). But I didn’t know how much oil was in it. I drilled a hole in the side to somewhat check level and added 80-90 gear oil. It was almost empty and added almost a quart. Used a self taping screw/bolt with gasket sealer to plug the hole. I got 34 yrs out of this washer. If it fails, oh well. Just hate to buy a new one that only last 10yrs if im lucky.
Parts Used:
-
Anthony from CHESANING, MI
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Screw drivers, Socket set, Wrench set
6 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer went off balance and the flume broke off
I removed the part that was still attached to the washer and installed the new flume. It took less than five minutes and a repair that would have cost over $85 cost less than $10 and I am no plumber!
Parts Used:
-
Michelle from Jupiter, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
13 of 27 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
new belt worn out by a bad motor pulley
i took off the old belt and i took off the motor pulley with the pliers and srewdriver. i put the new pulley in with my hand and gave it a hit with the palm until it snap in and then i put the belt on by rotating the main pulley on tub till the belt was pulley on.
Parts Used:
-
ALBERT from WASCO, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Pliers
7 of 9 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
No hot water was making it into the laundry cycle.
First I unplugged the machine, then turned the water supply off in order to disconnect the hoses at the back of the machine. Next I pulled the top up and leaned it back so I could access the water valve at the rear of the machine (You might have to use a screw driver to pry the top off the pins which hold it down in front...). I then unscrewed the the valve and disconnected the wiring and, in order, re-connected to the new valve. Now reverse and turn on the water and yes, the new valve fixed the hot water problem. We can now do the "whites".
Parts Used:
-
Neil from Ann Arbor, MI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Wrench (Adjustable)
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Topside door would not remain in an open position; lid hinges worn out.
The lid hinges are fastened to the top of the washing machine body, near the edge of the lid, with 1 screw each.
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!
To remove the old lid hinges, with the lid clamped in the open position, I needed to gain access to the screw heads from underneath, just inside the edge of the lid opening. To get at these screw heads, I needed to push the inside wash drum toward the screw I wanted to remove and wedge something in the gap created between the body of the washer opening and the drum, directly opposite the screw that I pushed the drum towards. What? This is to hold the drum completely out of the way while getting at the screw. My wedge was the handle of a squeege that just happenned to be nearby, but just about anything will work.
Once the drum was secure, I was able to get at the screw head, which, by the way, is a totally blind operation; you cannot see the screw head, only feel it. I guess we're kind of used to feeling our way around these days. Anyway, I had to repeat the wedging thing to remove the other lid hinge.
The only real problem I had was the original (factory installed) screw heads were hex heads, and I struggled a bit finding the correct size allen wrench to blindly remove the screws. It is a good thing that I also ordered 2 new screws along with the new lid hinges because the new screws have phillips heads. Much easier to work with, even though they were a little pricey. The old hex head screws were kind of worn and it would have been a cursing operation to try to reuse them.
Once the old hinges were off, I removed the lid, installed the new hinges on the lid and clamped the lid in place in the open position, while I screwed the new hinges on (wedging the drum out of the way like before). NOTE: It might be a good idea to line the wash drum with newspaper in case a screw slips out and finds its way into one the holes in the drum; lost forever. Anyway, this may sound like alot, but it really isn't. My wife didn't even comment on how the lid isn't smashing down on her any more. That's OK, I'm grateful I'm not the one doing laundry!
Parts Used:
-
James from Oakland, MI
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had water leaking from the top of the tub.
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
Parts Used:
-
Lester from Elk Grove, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
6 of 8 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Noticed nick in drive belt durng inspection and cleaning
Washer was making noise especially when spinning. I took the washer apart to clean it, That is what it really needed. Also adjusted the water level to prevent overflows which caused soap and water to get underneath into the drive belt area as well. During inspection noticed a nick in the drive belt, Although this was not really causing immediate problem wanted to repalce it to prevent problems. Ordered the belt; it came in two days with no special postage. To install, just leaned the washer over on its front on a slight incline. Took old belt off and put new on by turning the big pulley. It is spring tensioned, so no tools. This may be the easiest part repacement I ever did. Took longer to write this paragraph than to repalce the belt.
Parts Used:
-
Brian from Plainville, CT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Washer lid came off hinges
PROBLEM: The washer lid has two hinge pins that are attached to the lid with Phillips screws (one per pin). The plastic pin that inserts into the hinge broke off, allowing the lid to come free. SOLUTION: First, I removed the lid from the washing machine. Second, I used a Phillips-head screwdriver to remove the original hinge pins from the lid. Third, I replaced the hinge pins. Fourth, I used a flat-head screw driver to pry up the washer top to obtain easier access to the hinge screws. Fifth, I removed the original hinges with a Phillips-head screwdriver (one screw per hinge). Sixth, I attached the new hinges to the washer lid. Finally, I attached the hinges (and lid) to the washer top, then lowered the washer top.
Parts Used:
-
Geoffrey from Knoxville, TN
-
Difficulty Level:Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
5 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!