56031A0WW General Electric Washer - Instructions

First I unplugged the washer from the wall and then I removed the front panel with a putty knife. I slid the putty knife in between the front panel and top of the washer to disengage the two clips (see parts diagram on Partselect.com). Then I removed the four nuts holding the motor. I then removed the motor and old belt. I installed the new motor and new belt and tightened the four nuts ensuring proper belt tension. The new motor included a new wiring harness and capacitor. The wiring harness installation instructions were easy to follow. Besure to read the all the instructions first before beginning to cut the old harness. Once the wiring harness was installed, the machined worked just like new. I did not need the Retaining Clip for Clutch since the new motor and clutch kit come as one assembly and there is no longer an actual clutch. The two-speed motor just has a pulley for the belt.

the hardest part was getting the hub nut off. You have no room for a big wrench, I ended up chiseling it off.once I got it a part I saw the transmission was leaking oil, I checked every thing else, every thing seemed fine. I read on this web site that a common failure was the hub, mine was not in the best of shape so I replaced it while I was in there.replaced tub bearing,washer hub, hub nut , retaining clip for clutch,ring split, transmission and tub bearing 1/2 and $250.00 later the machine works like new.The diagrams that give you the part numbers were very helpful in the reassembly.

Removed the front cover of the washer by sliding a screw driver to release the clips. Loosened the 4 nuts that held the drivebelt motor pushed the motor back to release the drive belt. Replaced the drive belt, pulled motor until drive belt was snug and tighted the 4 bolts. At the same time, I replaced the 4 tub dampening straps located at the top of the tub and now the unit is just like new.

Took 4 screws off of face plate, exposed valve, unplugged power supply, removed wire harnesses to hot cold valves, removed hot and cold water hoses from back of washing machine, removed two screws holding valve body to washer,put new valve in and reversed procedure. ta da!!!!!!!!!!

Repaired Agitator - required to pull from the bottom pulling on one side a little more then the other. Once you got loose it comes right off. Under neith there is a bolt that holds on agitator coupler. remove the bolt with wrench or socket wrench and then the agaitator coupler. Replace with new agitator coupler ,make sure grooves are aligned when putting on the rotor. Tap the top of the agitator coupler lightly until it is completely seated. Put the bolt on with wrench or socket wrench. Put the agitator back on over the agitator coupler and agin make sure grooves are alighned and push down until it feels it is seated. When done, give it a light pull to make sure it is secure and then you are done.

drilled off top plate of agitator to gain access ot bolt, removed bolt, removed agitator, replaced coupler and new bolt, snapped in place new agitator.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

Removed washer to garage (after water was pumped out by the washing machines pump). Tipped it over to access bottom of machine and removed about 8-10 nut machine screws. Slipped new clutch on and used old retaining clip (new one was too difficult to get on). Loosened motor mounts on the drive motor and slipped on belt. Positioned the motor to put a good amount of tension on the belt and tightened motor mounts in a star pattern. Works great, even with heavy loads (like jeans). Easy easy.

followed the instruction on the wiring sheet and removal and repair sheet that comes with the wahing machine. They wee very good directions and the only problem that I had wa getting the 1 and 11/16 inch not off the shaft that holds the tub to the transmission, The main problem was that the transmission had leaked all over the break and the tub would spin while hitting the pipe wrench with a claw hammer. Ended up using a 10 lb sledge hammer to hit the pipe wrench and that finally loosened up the nut, but that was the only real problem i had. I say this was easy except for getting off that nut

I attached the Drain Hose Clip to the Drain Hose Extension and then pushed the drain hose all the way into the drain hole in the back of the machine. I then screwed the clip to the machine. Done. Very painless. Fast delivery... ordered it on Monday, arrived on Tuesday.

First removed front washer access panel.
Next: removed top panel torx screws and disconnected lid switch wiring connector
Next: removed washer top/lid
Next: removed inoperative lid switch (two phillips head screws)
Next: installed new lid switch and screws
Next: installed washer top and connected lid switch wire connector
Next: installed control panel and screws
Next: tested installation
Next: installed front washer access panel
Easy repair. FYI, Parts Select had best price and part arrived within two days of ordering! Highly recommend them for your parts.

Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.

First I removed the agitator with a belt. Then I removed the nut with a wrench. The Agitator coupli was smooth on the inside so I knew that was the problem. I got the new part, slid it into place. Tightened the new bolt and replaced the Agitator component with a quick push downwards. Easy!

I used the other 4 posting as a guideline but found that what wasn't mentioned here was that the disassembly/re-assembly instructions are actually located inside the washing machine behind the control panel (wish I knew that before I started doing it on my own).

After removing the control knobs (temperature, cycle, etc.), unscrew the four screws and lift the control panel off. Underneath the panel, there was a folded up wiring diagram that includes assembly instructions on the back.

Like others here, everything went smooth until I tried to get the Hub Nut (PS271505) off. No matter how hard I tried turning or hitting it (or the wrenches), it wouldn't move at all. I followed the other people's advise here and ended up taking a hammer and small chisel to the side of the nut. It's an aluminum nut so it cracked pretty easily and was easy to remove after that. Take my advise and just break the nut off if you are having any sort of difficulties getting it to turn. It's worth the extra $11 to just buy a new one!

I loosened the 4 screws that hold the motor and clutch in place. Removed the motor and clutch and turned upside down. Removed the retaining clip. Pulled the old clutch off (does not come off very easy). Stuck the new clutch on and replaced the retaining clip. Slapped it back into the machine.