4RF315PXMQ0 Whirlpool Range - Instructions

removed drawer below oven, reached under stove and unplugged from outlet, pulled stove out from between cabinets, removed the 8 screws with 5/16 nutdriver from back panel and removed the panel, removed knob from switch , measured length of stem on old switch and compared it to the new switch ( my old switch stems was shorter than the new one so using a pair of pliers I shortened stem per instructions that came with new switch, this was very easy to do ), removed the two screws holding switch to stove and removed the old switch, then I transfered one wire at a time from the old switch to the new one until I had all the wires connected to the new one, used same two screws holding old switch to the stove to mount the new switch to the stove and put knob from old switch onto the new one, installed back panel to stove using the same 8 screws, pushed stove back into place between the cabinets and plugged the stove into the outlet, put drawer back in place below oven door, reset clock and tried out the new switch, so far so good only time well tell if I fixed my problem because it only happens once in awhile

I discoverd my switch box locked with my stove electrical port and stove stopped functioning. Pulled my stove back and saw that the "terminal block" was melted on one side; hence, switch box locked in place to avoid a fire, thank goodness. Looked up part on internet, unplugged stove, took off terminal box, ordered part and replaced. BTW - PART SELECT is awesome; I received my part the very next day!!! :-) Very happy with their service.

I cut the ends of the cord and went with direct wire (no round eye clip) to the back side of the terminal block and tightened firmly. It took about 20 Minutes.

After searching on the internet for a very long time, we were almost ready to order the screws "blind" (no picture) from Sears for almost $10.oo per screw. Then I stumbled onto this website and found exactly what I was looking for, with a detailed description AND a picture!! Not to mention a price that was two thirds less than Sears..for TWO screws. Now the oven door is secure and we are no longer on our search for the right screws.

Removed oven door and the 3 screws holding the bottom door trim. Attached new trim piece and reinstalled oven door. Entire job took less than 5 minutes.

Removed the old burners and lifted top assembly. It made it easier to work with the wires by removing the top, easily remove the screws holding the wire harness and ground wire, then slid the top to the right and it came right off. splicing the wires in was very easy and all the parts required were sent with the kits. reassembled stove and it worked like a champ. The drawer was very easy as well the plastic glides were all broken or worn out, and one screw each to replace. like a new oven now, saved at least 300 by not purchasing a new one.

After removing the back of the stove, the old light socket was fairly easy to remove. The new socket slipped in place and the wires reattached and now the oven has a light again. A very simple process--especially for someone who's not an expert in repairing appliances.

Slide range out,unplug range,remove rear cover to unplug element wires, open door remove screws inside oven remove element

Shut down breaker; remove stove back cover plate (8 screws); remove the control knob; remove knob screws (2); simply remove one wire at a time and replace the coresponding wire to the new control unit; remove the snap ring on the knob bar and snap off to fit the proper length; place the control unit in position and reinstall the 2 screws; reinstall the back panel; position stove and turn throw the stove breaker on; test the burner control.

It was simple. Unscrewed to screws at the back of the oven. Slipped off the wire connectors then attached the wire connectors to the new part, put the screws back in and we were back in business.

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

First I disconnected the power, removed the screw that hold the element in place. Then, I pulled the element out and cut the two wires. I connected the two wires with the new element as the instruction provided by Part Select. I put the element back and screwed it in place. I plugged in the power and turned on the burner. It works. It is really easy to repair.

Removed the old, broken drawer glide by removing the Phillips head screw. Then placed the new glide into place and fastened with the existing screw.

The rivet on the top of the bottom drawer front was missing. I lined up the drawer front with the supporting bracket behind it and inserted the rivet. All you have to do is tap the top of the pin in the center of the rivet to lock it in place. No rivet tool is needed. That should be explained in the parts listing because I bought the rivet tool before I realized I didn't need it.

It was easy to find the part. I ordered it on Sunday and it arrived Wednesday. A stress-free experience.

Ordered a new switch and replaced the old one with it.