13-3620-00-02 Tappan Cooktop - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Original terminal degraded and faulty
Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.
Parts Used:
-
Robert from PRAIRIEVILLE, LA
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old drip pans had turned to rusty lace.
Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.
Parts Used:
-
Helen from PAWLEYS ISL, SC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Rusted Drip Bowls
This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.
Parts Used:
-
Carolyn from OCEAN PARK, WA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
replaced terminal block for element
-
Donna from UNION, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Terminal block was bad.
-
Chuck from EVANSVILLE, IN
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
needed new drip bowls and 2 new elements
pulled them out and replaced them
Parts Used:
-
kathy from DAVIS, CA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
OLD STOVETOP COILS
LOOKED FOR MODEL# OF STOVE.. ENTERED MODEL # IN PARTS.COM SEARCH.
MATCHED COIL AND DRIP PANS
ITEM NUMBERS AND SIZE.
PLACED ORDER.
ARRIVED FOLLOWING WEEK WELL PACKED.
PULLED OUT OLD COILS/DRIP PANS.
PLACE *NEW* DRIP PANS IN FIRST. THEN PUSH IN *NEW* COILS
**NO PAID INVOICE WAS RECEIVED**
Wed4/24/2024
MATCHED COIL AND DRIP PANS
ITEM NUMBERS AND SIZE.
PLACED ORDER.
ARRIVED FOLLOWING WEEK WELL PACKED.
PULLED OUT OLD COILS/DRIP PANS.
PLACE *NEW* DRIP PANS IN FIRST. THEN PUSH IN *NEW* COILS
**NO PAID INVOICE WAS RECEIVED**
Wed4/24/2024
Parts Used:
-
SANDY from TOMAH, WI
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
uneven heating
Repair failed because part did not fit. Offset between top of element and contact prongs was too small, so element could not sit flat.
Parts Used:
-
Dan from CHEWELAH, WA
-
Difficulty Level:Very Difficult
-
Total Repair Time:More than 2 hours
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drip bowls needed replacing
Removed the old ones and inserted the new ones.
Parts Used:
-
Doris from SUN CITY, AZ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Left an appliance on surface element and melted paint onto the element
-
Kenneth from LANOKA HARBOR, NJ
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner would cutoff intermittently
-
Joseph from FREDERICKSBRG, VA
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 person
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
old drip bowls
-
Vera from Snow Camp, NC
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Pulled the heating element on each burner installed the drip pans.
They fit perfectly for this stove. I had bought some drip pans but definitely not the correct pan. Saved time and about same at stores price. Great service thank you will order elements next. Pull heating elements remove drip pans and replace with new pans ,replace heating element. Done
Parts Used:
-
Sharon from AURORA, MO
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
This is for a basic four-burner electric stove:One element was bent so I replaced it and all of the drips bowls needed replacing.
The element pulls out easily and slides right back in and the drip bowls just lift in and out. TaDa !!
Parts Used:
-
Olivia from FAIRLEE, VT
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Burner on stove stopped worker
I did as instructed on your video of how to install the terminal block, btw GREAT VIDEO!!
I'm a 66 year old female and if I can do it, anyone can.
Thanks, PartSelect
I'm a 66 year old female and if I can do it, anyone can.
Thanks, PartSelect
Parts Used:
-
Virginia from MT PROSPECT, IL
-
Difficulty Level:Very Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Screw drivers
1 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!