1106008714 Kenmore Dryer - Instructions

This was rather easy to fix. I had never opened the dryer before but had a serviceman come out so I knew that you can pop the top of the dryer off by putting a flat edge screwdriver in between the top and bottom and popping up. You must remove the screws from the lint dryer before so the top comes off. The piece to replace had two screws and that was it. To get a repairmen from Sxxrs where we purchased it 15 years ago they charge a flat fee of $75 just to come out. That does not include the repair just a fee to come and tell you how much more it would cost to fix it. I ordered the part for less than $5 and $12 more for 2-3 day delivery! What a bargin! I was back drying clothes 15 minutes after the part arrived! Very happy that the part is still being made!

Before beginning, unplugged dryer. 1) Used putty knife at each front corner of top to pop lid loose from clips. 2) Removed hex screws at back of control panel to allow lid to tip open. 3) With lid opened, removed hex screw from inside-top of each side to allow front to pull open from side panels and access door switch easily. 4) Removed clip that holds retaining wires from top. 5) Pulled wire from each side of door switch. 6) Removed switch assembly using Phillips screwdriver to remove two screws mounting switch at top of door opening. 7) Removed broken actuator spring and replaced. 8) Reversed process to reassemble.

I replaced the male end first hoping that a change in the female part would not be needed. Unfortunately no. I used needle nosed pliers to pry the male part out and pushed the new part in. The female part of the door catch was more difficult. I didn't do it in "textbook" form, but got the job done with pliers and a screwdriver. Worth every penny to fix correctly instead of rigging it. Do it!

After removing front door panel (2 screws) I removed the old latch catch and replace with the new part. 4 minutes later, the door was back together, the dryer was running and the door was staying closed.

The only thing I had to do was hammer the catch inside the square fitting and presto it was done. It took me less than 3 mins. I thought I might of needed instructions, but it was really simple. Even a guy can do it. (smile)

just put the new part in the door---sooo easy! THANK YOU!

I removed the two screws on the top by the lint catcher. Then, per information from this website, I pried up the top. I reached down into the dryer and removed the two screws on the broken door switch and replaced it with the new part. I am a recently widowed, 55 year old and was thrilled to find good advice, information and instructions on your website!! Simple as could be!

Got my parts very quickly.
Popped out the old door latch with a screw driver and pressed in the new one.
Very simple.
Thanks Parts Select.

Pop out the old latch and replaced with a new one

Just slipped it on, it was very simple. My dry cylces were reduced. Worth the $15 I spent to get the part!!!!

took the cstch reciever out, with my fingers, pushed the new one in, snap lock fit.......couldn't be better, like repairing a model T ford.......

the part fit perfectly, it just snaped right into place.

I took out the 2 screws that are located on the top of dryer under the lint filter door. Popped up the whole top of dryer. Opened the dryer door to unscrew the 2 door switch screws. Took off the old broken door switch through the open dryer top and before replacing the new door switch completely I tested it by turning the dryer on and pressing the new switch against the button activator 2 find out if it works. When it did, I carefully put the door switch back so the dryer door can activate it properly and screwed in the 2 screws. Finally, I put the dryer top back down & fastened the last 2 screws under the lint filter door.

Followed video on PartsSelect website, they made it real easy.

Removed what was left of the old hinges, installed the new ones. Also added a length of jack chain (same size chain that’s on a toilet flapper) to one side to support the door while open. Tried to chain up both sides but it wouldn’t let the door completely close and depress the switch. Cables are no longer supplied by any parts dealers.