![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)
Part Videos
Replacing your Frigidaire Refrigerator Evaporator Fan Blade
![Replacing your Frigidaire Refrigerator Evaporator Fan Blade Replacing your Frigidaire Refrigerator Evaporator Fan Blade](https://img.youtube.com/vi/u951HFLXDJg/maxresdefault.jpg)
Troubleshooting
This part fixes the following symptoms:
Noisy | Fridge too warm
This part works with the following products:
Refrigerator, Freezer.
This part works with the following products:
Frigidaire, Kenmore, Gibson, Kelvinator.
Part# 5308000010 replaces these:
AP2152058, 1083, 08000010, 216325600, 218649000, 3001215, 3001357, 75308000010, 8000010, C000040268, C000048770, C000048771, C000071211, C000071213, C000289200, C48770, G000126599, G000174705, G126599, G162599
...
Show more
, G164094, G174705, G185153, G98355, G98356, K1202161, K1202162, K1203079, K1209388, R000900758
Show less
Customer Reviews
Filter By Rating:
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
Bruce H - July 13, 2021
Verified Purchase
Preventative purchase
I’ve been concerned for awhile about my noisy fridge. I traced the noise to the fan/motor in back of freezer compartment. However it still works well; I monitor temperature with a couple sensors in fridge and freezer. I now have the parts on hand (fan, motor) to repair if it fails so I’d only lose service for a short time, and likely no lose of food. No issue with the parts, and your part replacement videos remove any apprehension around doing my own service.
- < Prev
- 1
- Next >
Customer Repair Stories
Average Repair Rating: 3.4 / 5.0, 6 reviews.
What's this?
- < Prev
- 1
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Noisy fan
1. Removed the 7 nuts using the nut driver from the freezer back panel inside the freezer.
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including the brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
2. Remove the back panel. The evaporator motor and fan are located above the coils.
3. Unplug the wiring harness.
4. Remove the two gold mounting screws holding the motor and fan in place.
5. Remove the motor and fan including the brackets.
6. Install the new motor and fan onto the mounting bracket.
6a. Attach the green ground to the mounting bracket.
7. Screw the two gold screws back into the freezer.
8. Attach the new wiring harness. Note, the old harness had a mounting hole/space for it to connect to the wiring harness of the freezer. The new motor's harness was not long enough for this, so it is connected freely to the freezer harness.
9. Use the hair dryer to melt any ice that may have formed on the coils and hole where the fan goes.
10. Turn the freezer on to see if the fan turns on.
11. Reinstall the back panel.
All done!
Other Parts Used:
-
Jordan from Maumee, OH
-
Difficulty Level:Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver
153 of 180 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
lighting hit the house
first i by passed the timing board, with a ele cord to the fan motor to keep the fridge cool till your parts got here, which was realy fast delivered,
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts
the fan would come on because the board was fried.
it took abot 30 min to install every thind just be carefully unpluging anything.things will break i guess metal eing cold makes the conne4ctors stick together.
evaporator fan is in the frezzer four screws,tested the wires for ohms,and power, when i pluged in the fan i would loss power to the fan,that told me the board was bad, the same night my furnance when to (reaaly) and i lost my borad on the computer ethernet card (lighting isn't fun) it cost to fix everything about 130.00 thanks for thr great parts
Other Parts Used:
-
keith from villa rica, GA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
31 of 57 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Evaporator Fan Burnt Up
The fan motor all but caught the inside of the freezer on fire . Had to remove then clean, and I mean clean the walls of the freezer . Then had to pry out the old fan without breaking anything . Replacement of new fan was quick and easy because all the parts that I needed were in the bag
Other Parts Used:
-
ROY from PENSACOLA, FL
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:1- 2 hours
-
Tools:Pliers, Screw drivers
28 of 38 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Freezer making annoying high pitched sound (like a whine)
Parts Select included a video, and I watched a couple more that were on YouTube. Watch the video and do the repair . . . it's very easy took me about 35 min once I got the freezer emptied, including cleaning the freezer. I used a Philips head screw driver and I think it was a 5/16 nut driver . . . you can do this. Freezer running fine, no noise. One thing I would be careful on is removing the back plate that covers the fan and motor, the edges can be sharp and you could cut yourself removing the back plate. Also don't try to put the rubber gasket in before you replace the back plate, install the back plate and the rubber gasket goes in easy peasy :)
Other Parts Used:
-
Greg from NAVARRE, FL
-
Difficulty Level:Very Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Screw drivers
4 of 4 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I had a broken fan blade due to ice build up from a leaking ice maker.
1. I took out one screw on the ice maker and loosened the other two screws and unplugged and removed the ice maker.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
2. Next I took out 2 screws from the bottom of the auger drive box and unplugged the wiring harness and removed the box. The wiring harness was a little tricky. The lock on the plug pushes in to unlock even though it looks like it pulls out,.
3.next you must remove 2 screws from the left side bracket that holds the auger box and remove the bracket.
4.Now take out 8 screws that hold the back panel in place and remove the back panel.
5. now your looking at the evaporator fan blade and motor. The simple way to replace the fan blade is to unplug the motor and remove it from the freezer. It just sits in with nothing holding it. The fan requires a little pressure but should pull right off. Install new fan blade and put everything back in the same order it was removed.
Other Parts Used:
-
gary from ARANSAS PASS, TX
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Nutdriver
3 of 5 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
loud noise fan blade broke,off balance
take 1/4 hex screws out clean out dust ,remove old fan blade replace with new install bolts .
Other Parts Used:
-
EDWIN from ELWOOD, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
- < Prev
- 1
- Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
- < Prev
- 1
- 2
- Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Comstock
August 27, 2017
Is there video to walk me through this process? What tools are required?
For model number FRS26RC3JS3
Hi Comstock,
Thank you for the question, The tools needed to complete this repair are a 1/4 inch nut driver and a pair of needle nose pliers. Here is a link to our video.
https://www.youtube.com/watch?v=Hj_ojPQebcw
Hope this helps!
![](https://img.youtube.com/vi/Hj_ojPQebcw/maxresdefault.jpg)
9 people found this helpful.
Was this helpful?
Thank you for voting!
Pamela
November 24, 2017
Hi I recently purchased the defrost kit from you and it seemed to work immediately for about two weeks. Now I am experiencing the same issues as before. Fridge and freezer are too warm and a clicking sound was being heard, frost has built up on the bottom half of the freezer panel in this short time. What would be my next step?
For model number flsc238js1
Hi Pamela, Thank you for the question. With the information provided, you may have an issue with the Main Power Control Board,PartSelect Number: PS2339026.You can also test the Defrost Thermostat.
The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Earl
December 11, 2017
Evaporator fan making noise.
For model number FFHS2611WHA
Hi Earl, Thank you for the question. If the fan is making noise, I suggest having it replaced. Good luck with the repair!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Mary
August 4, 2018
Lights are on and i hear refridgerator running but it does not cool down at all and then it shuts off
For model number 25370413414
Hi Mary,
Thank you for your question. If the refrigerator is too warm, there are some parts that you will need to check to see which ones are causing the issue. You will need to check the evaporator fan blade, the evaporator fan motor, the temperature sensor and the filter-drier. I hope this helps. Thank you and have a great day!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Clyde
November 6, 2018
I have an intermittent noise coming from freezer. I think it may be this fan. Does this fan run continuously? If so, is there any reason the noise would be intermittent? Is there a way to test that this fan is the cause of my problem?
Hello Clyde, thank you for your question. The fan does not run continuously. It turns on and off to blow cold air into the fridge from the freezer. You're probably hearing the noise when the fan is running. I Would recommend removing the cover on the back of the unit to make sure the blade isn't hitting ice that has built up on the coils. If there is lots of ice buildup you would have a different issue and then we could provide some more information on the potential parts. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Phay
November 21, 2018
Hello, is this fan blade (evaporator fan blade 5308000010) compatible with the evaporator fan motor kit 5300158289?Thank-you
Hello Phay, thank you for your question. Yes, the blade part number 5308000010 is compatible with that fan motor. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Gerald
June 26, 2019
Have ice build up behind panels in back of freezer side. Ice hits fan and noise starts. Fan works but wondered if thermostat would be problem. Have had sy ef reading on control board but unplugged and defrosted and went back to working.
For model number FGHS2631PE3
Hello Gerald, Thank you for the question. I suggest testing the Defrost Thermostat Kit, PartSelect Number PS469522. The best way to do this is to remove the thermostat from the refrigerator so you can control the temperature of the sensor. You can let the sensor warm up to room temperature. With the sensor warmed up to room temperature the sensor should read approximately 6.2K Ohms at 68°F. With the thermistor submerged is a glass full of ice water, the sensor should be very close to 32°F which should read approximately 16.3K Ohms. If the values that you are getting are far off from these readings, then the sensor is bad and should be replaced. Hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Related Parts:
Jerry Burkhart
October 2, 2019
Is this freezer. Frost free?
For model number FFU1466GW1
Hello Jerry, thank you for writing. A frost buildup can occur from either a faulty Defrost Thermostat, part number PS2350702, or Timer, part number PS12585793 for your model. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Joanne
February 13, 2020
Fridge and freezer will not sustain correct temperatures, keeps defaulting to 'h' or '1' and '1'
For model number FFHS2322MBLA
Hello Joanne, thank you for writing. We advise checking the Run Capacitor. When testing a capacitor with a multimeter, you will need to set the meter between 10K and 1m ohms. Touch the leads from the multimeter to the corresponding leads on the capacitor. The red lead to positive and the black lead to the negative. The meter should start at zero and then moving slowly toward infinity. This means that the capacitor is in working condition. If the meter stays at zero, the capacitor is not charging through the battery of the meter, meaning it is not working. I hope this helps.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Felicia
September 1, 2021
Frig is normal then it will get very loud, it will stop when you open the doors or the drawer for the freezer but will start back when you close them. Sometimes it sound like a drill.
For model number LGHB2867PFGA
Hello Felicia, Thank you for the question. Normally this is caused by a defective Refrigerator Evaporator Fan Motor. We suggest checking the fan to make sure the blades are not loose as well. We hope this helps!
Was this helpful?
Thank you for voting!
Related Parts:
- < Prev
- 1
- 2
- Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
Sorry, we couldn't find a match for "".
Here's a guide for finding your model number.
Something went wrong. Please try again later.
Your Question Has Been Submitted!
Our experts will send you an email as soon as your question has been answered.
Related Parts
Model Cross Reference
This part works with the following models:
PartSelect Number: PS473177
Manufacturer Part Number: 5308000010
Manufacturer Part Number: 5308000010
Brand
Model Number
Description
![Customer Service Representative](https://partselectca-dsfph5cffxaaesb6.z01.azurefd.net/images/csr-partdetail.jpg)