This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
$10.20
In Stock
Order within the next 11 hrs and your part ships today!
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
$72.91
In Stock
Order within the next 11 hrs and your part ships today!
This is a replacement tub-to-pump hose for your washer. This hose runs from the bottom of the tub to the water pump, and is used to transport water. The hose can develop a hole, and when this happens ...
$43.62
In Stock
Order within the next 11 hrs and your part ships today!
Water inlet valve controls the water flow into the washer.
Fits some washers in the following series: Kenmore 110; Whirlpool CHW, WFW and YWFW; Maytag CHW, MHN, MHP, MHWE, MHWZ and YMHWE; Amana NFW...
$151.54
In Stock
Order within the next 11 hrs and your part ships today!
This is the replacement bellow clamp for your washer. It is approximately 18 inches in diameter and is sold individually. The bellow clamp goes around the bellow in your washer and holds it in place o...
$36.37
In Stock
Order within the next 11 hrs and your part ships today!
This part is the replacement drive belt for your washer. It is made of black rubber and is approximately ½ an inch wide and 48 inches long. It has 6 grooves and is sold individually. The drive belt is...
$64.15
In Stock
Order within the next 11 hrs and your part ships today!
Questions And Answers for YWFW9050XW01
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Carol
January 30, 2023
Water does not go into the softener and bleach dispenser. It quit working after I took the dispenser out to clean the water. It is nine years old.
For model number YWFW9050XW01
Hello Carol, Thank you for reaching out. We suggest checking to make sure all the Hoses are connected to the back of the Drawer and the water to the appliance is turned on. If everything is properly connected you can test the Water Inlet Valve. Set your multitester to the ohms resistance scale X 1. Place each of the meter's probes to one terminal. Because the reading can vary from brand to brand and from model to model, there is no one reading you should receive. However, if your test produces a reading of infinity, then the solenoid is bad and the water valve should be replaced. We hope this helps!
Clothes torn during wash. Sometime really bad. During every wash some clothes worn out badly. Please reply.
For model number YWFW9050XW01
Hello and thank you for writing.
During the spin cycle, the agitator goes even faster to help dry the clothes. If you're experiencing torn clothes in your washing machine, there's a good chance it could be related to the agitator such as a bad motor pulley PS11746256. Once a shirt or pair of pants gets caught up around it, the agitator can rip them apart. We hope this helps. Please contact us anytime if you require further assistance.
power outage and resetting breaker does not fix our problem. lights are blinking and it wont start or reset.
For model number YWFW9050XW01
Hi Lisa, thank you for reaching out. We have found that the issue is with the control board, part number PS11750473. Our suggestion here would be replacing the control board to fix the issue. We hope this helps, good luck with this repair!
Removed the front panel unplugged The washer drained water out, lift the washer up to un screw the drain pump. Then unhooked the hoses from pump put the other pump in.
Pump started making noises like ball bearings grinding. took the lower front cover off pulled the strainer out of the pump housing and found $2.55 in nickles dimes and quarters. Some 223 bullets and about 20 bobby pins. Together they had destroyed the impeller, so ordering a new one and installing it did the trick. Easy installation about 15mins.
This model is a front-loading washer. The spring loaded retainer for the front of the boot must be removed, then the boot can moved to the side exposing the module. Remove the two screws holding the model, pull the model out, remove the three electrical plugs, then reverse this procedure to install new module.