This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
This drum shaft assembly is for washers. Drum shaft assembly connects the spin basket to the drive motor to spin the basket. Unplug the washer before installing this part. Wear work gloves to protect your hands.
This lid hinge is a genuine OEM replacement part for your washing machine. This hinge is for the left side of your lid, although it is a good idea to replace btoh hinges at once. The hinge holds up th...
$32.30
In Stock
Questions And Answers for WTW8040DW2
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Tammy
December 3, 2019
Had a power surge and now the washer will not power on.
For model number WTW8040DW2
Hello Tammy,
Thank you for your question. Our sources suggest you check the electronic control board to see if it is defected, if the washer isn't working after a power surge, usually the control board is fried and would nee to be replaced under part PS11723055 for your model. Hope this helps!
The machine will fill and work if you select hot water but will not fill and work on cold?
For model number WTW8040DW2
Good Day Christopher. Thank you for your question in regards to your unit (Model Number WTW8040DW2). Based on our research, this could be the result of clogged debris in the hose that supplies your unit with cold water. You may need to disconnect it and check to see if this is so, and clear it of the debris. This also could be the result of a faulty valve or wiring problem that may need to be replaced on your unit. We hope this helps. Best Regards.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Connie
February 28, 2020
Will not spin after last drain. Have to select manually.
For model number WTW8040DW2
Hello, Thank you for your question. You will want to check the motor and the timer area, those are the main causes for the issue you are having. We hope this helps.
Was this helpful?
Thank you for voting!
Ken
May 6, 2024
Sounds like a jet taking off and DR code comes on and will not finish cycle
For model number WTW8040DW2
Hi Ken, thank you for the question. Based on our research, the DR error code means that there is a drainage issue and the washer is taking too long to drain water. We would suggest checking the drain hose for clogging first. If it is fine, the issue could be with the drain pump, part number PS11738156. You may need to replace it fix the issue. We hope this sorts out your problem!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
This is a very simple repair. My lid was severely cracked on the back left corner where there seems to be a lot of pressure/torque required to shut the lid. There is a metal L-shaped "tab" that inserts into the lid on both sides of the back edge of the lid. The lid is attached to these metal tabs with two screws for each side. My cracked lid had resulted in the lid breaking off of the metal tab with the screws still anchored into the metal tab.
Make sure screws have been removed from the metal tabs on both sides. Do not remove metal tabs- leave them attached to the washing maching (otherwise, you will not be able to attach the lid back onto the machine). Slide the lid over the tabs. There are square-shaped spaces along the edge of the lid where the tabs slide into the lid. Re-screw the screws into the lid, attaching the lid to the tabs through pre-drilled holes on the sides of the lid. It may take a little time to make sure the screws are properly inserted into the lid and tab screw holes. Tighten up and you're finished.
