The drain pump and motor assembly may also be known as the washer drain pump and is a part for your washer. The drain pump helps expel water from the washing machine. The drain pump is activated after...
$156.41
In Stock
Order within the next 4 hrs and your part ships today!
This valve is used for cold water, bleach dispenser and prewash cycles. It has a standard hose fitting inlet with 2 outlets facing 45 degrees to the right and one outlet facing 45 degrees to the left.
$135.21
In Stock
Order within the next 4 hrs and your part ships today!
This washer hose with bellows, also known as a dispenser hose, is a genuine OEM replacement part for your washer. Replacing this part can be helpful if your washer is leaking. The dispenser hose conne...
$62.02
In Stock
Order within the next 4 hrs and your part ships today!
This door boot is for washers.
Door boot forms a seal between the wash tub and the door, preventing leaks.
Unplug the washer before installing this part. Wear work gloves to protect your hands.
$228.40
In Stock
Order within the next 4 hrs and your part ships today!
This tub bearing is for washers.
Tub bearing supports the spin basket shaft at the tub.
Unplug the washer and shut off the water supply before installing this part. Wear work gloves to protect your hands.
$71.07
In Stock
Order within the next 4 hrs and your part ships today!
This is a replacement detergent dispenser for your washer. It stores the detergent, and then dispenses it into the washer at the appropriate point in the wash cycle. If the detergent dispenser is brok...
$35.82
In Stock
Order within the next 4 hrs and your part ships today!
This part is the replacement rear tub gasket for your washer. It is made of black plastic and is approximately 3-1/4 inches in diameter. The rear tub gasket forms a watertight seal between the rear tu...
$39.26
In Stock
Order within the next 4 hrs and your part ships today!
Questions And Answers for WM3170CW
Ask our experts a question about this model and we'll get back to you as soon as possible!
1 question answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dale
February 28, 2024
Washer does not spin
For model number WM3170CW
Hello Dale, thank you for your inquiry. According to our understanding, we would recommend checking the stator assembly for any blockage or fault. If it is fine, then the issue is most probably with the drain pump, part number PS3579318. You may need to replace it to fix the issue. We hope this helps!
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer came apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.