WCCD2050FW General Electric Washer - Instructions

1. Drained the wash tub by taking the drain hose from the back of the washing machine and dropping it below the tub - water flowed out of hose a lot easier than trying to suck water out of tub using a pump (tried this on the first time I tried to fix washer). (Washing machine on 2nd floor of house and didn't want water running on floor)
2. Removed the 2 bolts holding the Pump/Motor assembly to the machine.
3. Removed both hose clamps on the Pump/Motor assembly and removed Pump.
4. Attached the new drain inlet hose to the pump and then to the tub with the original hose clamps.
5. Attached the drain hose to the pump and then plugged in the 2 wires for the pump.
6. Plugged in the washing machine and everything worked.

NOTES:
1. Hardest part was working with hose clamps (spring type clamps) in the tight space under the machine.
2. Easier to fix since I pulled machine apart a few days before - removing the clog in the pump/motor assembly only to get everything back together to find out that the motor was dead. Still well worth the time and effort due to not having to go out and buy a new Machine...

Removed front cover, Control panel, top Cover, slasher unit, all very smiple stuff. the hub was broken and the spinner basket came right out. One half Hub attached to Spinner, Other half attached to Hub drive shaft. removing the Hub nut was the hard part. tried impack & socket, No luck. in removal. Had to usr Hammer & Chisel and bust Old Alum. Nut off. Clean up and replace parts. OK. Had to remove water pump and clear debree that went in pump when spinner Hub broke off . the spinner also bursted a crack in the outer poly tube when it cam apart.. Sanded the dmage area and Patched with a good coat of JB Weld. machine is working Like new. The parts all worked Great. the break down Chart was a great Help to get the right parts needed. Thanks

Aside from getting the wet clothes and most of the water out,the toughest part of the job for me was to figure out how to get inside the machine. I nearly wrecked the thing trying to lift the top panel. After some frustration I removed the star-type screws on back of the control panel and found, tucked away neatly, the documentation/parts list complete with instructions on how to remove the FRONT panel. Once I got inside it was easy to locate the pump. I ran the drain cycle for a moment to see if the pump turned at all. The original had an exposed fan so it was easy to see that indeed the motor was not turning. I inspected all the hose and electrical connections to make sure I had the tools I'd need and the savvy to replace the part(s) if I could locate them. I'm not much of a web-head, so I was a little surprised when I typed G.E. appliances and the search took me to partselect.com where I was pretty much coached through the procedure before I even ordered the part. The box arrived ahead of schedule (yay) and when I looked at the pump it didn't look much like the one I was replacing. But then I realized it was the same thing just ten years more advanced. I used a small pair of vise grips to pinch and lock the pipe clamps open. I know there is a plier made for this, but... Anyways, after loosening the clamps and sliding them away from the pump I pulled the hoses off and let the last of the rinse water still in them run down my shirt sleeve to my elbow. (optional, not recommended) Thus refreshed I then rummaged through my socket set and found what I needed to remove the 2 sheet metal mounting screws and disconnected the 2 power leads. I removed the faulty pump and proudly showed it to my wife. Unimpressed, she asked how much longer. I quickly reversed the procedure to install the new unit and confidently piled in a load of laundry. The cycle completed just fine and has done so since. I will and have recommmended partselect.com to friends and will use it again for sure.

First I removed the front panel by prying it forward with a Screw driver away from the side panels at the top (wrap a shop rag around the Screw driver to keep from scratching the paint). Once you have the panel pried loose at the top ... lean it forward until you can lift it off the tab type hooks at the bottom.
I next unplugged the wires from the motor. The orginal motor had three wires ... two on top and one on the left side. The one on the side is a ground wire for the open frame motor. The replacement motor is sealed and does not require this wire. Just leave it unplugged when the new one is installed.
Next I removed the inlet hose that attaches to the back of the pump. Remove it by loosening the hose clamp and removing it from the bottom of the tub, leaving it attached to the back of the pump. It is much easier to remove and transfer to the new pump once it is out rather than fight with the spring type clamp on the back of the pump in the close quarters inside the machine.
Next I removed the outlet hose from the top of the pump. Squeeze the spring clamp with Pliers and work it up and off the pump.
Now I just used a Socket to remove the two bolts holding the bracket to the inside front of the machine and removed the assembly.
I now removed the inlet hose from the back of the old pump. Just squeeze the spring clamp with Pliers and work it up the hose and off the pump. Transfer the hose to the back of the new pump reusing the same clamp.
I now bolted the assembly back into the machine, reattached the outlet hose to the pump, and then reattached inlet hose to the bottom of the tub. All that was left to do was plug in the two wires to the top front of the pump motor (as I mentioned earlier, leave the side wire from the old pump unplugged as it is not needed on the new one). I then ran the machine for a few moments with the front off to check for any leaks and then put the front panel back on.
The whole replacement cost about $50 and took barely 15 min. from start to finish. The machine now works perfectly.

I replaced the work tub dampening strap because that what everyone recommended to replace for this problem. However the purpose of these straps is to dampen the agitation cycle and they have nothing to with the spin cycle at all. the balance ring assembly had been rubbing on the outer tub so I decided to replace it because of a "balance issue". However the ring is liquid with baffles to counter balance the load as it spins and it still had the liquid inside of it so it was actual not needed. What fixed my issue was I found a bolt laying at the bottom of the washer. This bolt was one of the 4 bolts that hold the outer tub to the metal support. When it feel out the tub was only held in at 3 points not the needed 4. This allowed it to rock a bit in the high speed spin and you thought it was going to fly into a 1000 pieces. I replaced the bolt and other parts since I had paid for them and everything works great now.

removed hoses and clamps. removed 2 bolts on pump. put it back together. done 15 min.

Thanks to comments already summited to Partselect I was prepareed for the worst. Once I figured out that you remove the agitator assembly with a swift jerk I was able to access the lower portion of the tub. As others have found out the aluminum nut holding the inner tub can not be removed without a hammer and chisel. Once you get past that things go well. What is left is cleaning the components and re-assembling.

I used the other 4 posting as a guideline but found that what wasn't mentioned here was that the disassembly/re-assembly instructions are actually located inside the washing machine behind the control panel (wish I knew that before I started doing it on my own).

After removing the control knobs (temperature, cycle, etc.), unscrew the four screws and lift the control panel off. Underneath the panel, there was a folded up wiring diagram that includes assembly instructions on the back.

Like others here, everything went smooth until I tried to get the Hub Nut (PS271505) off. No matter how hard I tried turning or hitting it (or the wrenches), it wouldn't move at all. I followed the other people's advise here and ended up taking a hammer and small chisel to the side of the nut. It's an aluminum nut so it cracked pretty easily and was easy to remove after that. Take my advise and just break the nut off if you are having any sort of difficulties getting it to turn. It's worth the extra $11 to just buy a new one!

Unplug the washer. Turn off water supply. Disconnect hoses and have a bucket to catch the water standing in the hoses. Unscrew the 4 screws on the top of the control panel (my model had torx head screws). Flip down the control panel. Unplug the triple water valve. Disconnect the hose clamp from the water valve. Unscrew the water valve using a 1/4" nut driver. Replace with the new valve in reverse order. If your washer is older I would recommend also purchasing the hose & water inlet (number 803 on the diagram) I was afraid that mine would crack when I removed it. It was a very easy repair and I am happy that I did not have to pay a repairman to fix thia problem.

Removed front cover, lifted lid. Unnapped the broken tub cover pulling the tub forward to allow the old cover to clear the rear of the housing/top. Installed the new tub cover by once again doing the same thing and carefully snapping it into place. Reconnected the rubber sping offloads, lowered the top and reinstalled the front cover..ready to run.

The video with Steve is invaluable. I followed the video to replace the tub bearing. Had to jump over to the tub seal video to make sure I got it seated into the outer tub correctly. The tub bearing video skips past the seal part. Be aware that the video cut aways can be a considerable amount of time. Highly recommend a few things: 1) if you think you need to replace one of the things on my parts list (bearing, washer, seal, etc) then just replace everything at once. It's not worth it to try to reuse old nasty parts. All of the parts + 1 11/16 spanner wrench came to around 60 bucks. 2) get the washer out of its confined area and give yourself some room to work on it. I took the time to shuffle it out into my garage and setup a table to spread out the parts and tools. This procedure is a complete washer dismantle job. So take your time and be patient. 3) the aluminum hub nut is a bugger. I had to use penetrating oil and make a couple of small angled cuts with a hacksaw to relieve the tension between the nut and transmission shaft. 4) the main lower tub bearing (bushing) was also a bugger and all gummed up and rusty. Be very careful getting it out. You don't want to ruin the integrity of the outer tub cavity that it goes into. Light taps and patience using the butt end of a hammer and flat blade screwdrivers. From beginning to end, with a few breaks to let the penetrating oil do its thing, it took about four hours. I took my time, reviewed the videos throughout that time, and I've never worked on a washing machine before.

Used the repair instruction paper behind the washer control panel and used the online parts diagram. Also the online responces from other customer repairs gave me the idea to take a small pipe wrench (with a sock over the bottom of handle) and tap it with a 10 lb sledge hammer to remove the alumium hub nut. *** It is a backwards threaded nut **** I did not know I was going the wrong way until I looked at the new nut and noticed it's reverse threaded!!! After that it was just taking everything apart and putting it back the way you found it.

1) Disconnect power
2)remove front panel
3) remove screws and take hoses off
4) remove & replace water pump
:) YAY. all done

Biggest problem was getting old hub nut off. I had to remove it in pieces because it was corroded so bad.

Once hub nut was off it was a breeze to replace the parts after cleaning off the threads and shaft.

Reassembled in reverse order.. and ran.

I have to give accolades to PartSelect.. their customer service is second to none. i ordered the parts just before the Christmas holiday and they shipped them to my door in under 24 hours at no extra charge to see that I got them on time...
THANKS!.. It sure helped.

Would I do business here again.. YEP!

I will recommend you to others.

Thanks.

Remove aggitator, disconect 4 support straps, pry off clips/ latches on top of drum. Remove small bolt that holds on the small plastic unit unto trans.
That will give you access to the large bolt that holds the hub in place. This nut is on tight use a pipe wrench and adjustable wrench and TURN CLOCKWISE TO REMOVE - lock for direction on nut.
Remove the bin gently and turn over to remove the small bolts that hold the hub in place.
Installation is reverse of removal.