Models
>
SE1000
SE1000 Maytag - Overview
Models starting with SE1000
Click on the best match to narrow your results.
Keep searches simple, eg. "belt" or "pump".
Drum Support Roller Kit
PartSelect #: PS1570070
Manufacturer #: 12001541
This drum support roller includes one drum roller and two bearings. Most dryers use two drum rollers, and it is recommended to change both at once.
$19.12
In Stock
Tumbler and Motor Belt
PartSelect #: PS11757542
Manufacturer #: WPY312959
The tumbler and motor belt in your dryer allows the drum to spin during the drying cycle. At 100 inches in length, this dryer drum belt is 3/8 of an inch wide and has five ridges. The belt is black in...
$41.42
In Stock
Roller Shaft
PartSelect #: PS11743031
Manufacturer #: WP6-3129480
This roller shaft is the axle for the drum roller, also known as drum roller axle.
$12.51
In Stock
Front Glide Kit
PartSelect #: PS1804752
Manufacturer #: 306508
This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
$18.74
In Stock
Blower Wheel with Clamp
PartSelect #: PS2200270
Manufacturer #: Y303836
This blower wheel comes with a metallic hub clamp to hold it firmly in place.
$29.17
In Stock
Belt Kit
PartSelect #: PS2005284
Manufacturer #: 12112425
This kit includes both the drive belt and the pump belt which are both "V" shaped.
$52.60
In Stock
M Series New Style Coil Kit
PartSelect #: PS334310
Manufacturer #: 279834
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them ...
$39.39
In Stock
Lint Filter
PartSelect #: PS11741039
Manufacturer #: WP33001003
This lint filter screen is slide in styl type of Maytag filter screen. It is most typically used for the 08 and later series of Maytag gas or electric clothes dryers that appear before 1990.
$31.94
In Stock
Retaining Ring
PartSelect #: PS11746909
Manufacturer #: WP9703438
This metallic retaining ring is less than an inch in diameter. It is made entirely of metal.
$10.05
In Stock
Drum Roller Shaft Washer
PartSelect #: PS11740748
Manufacturer #: WP312535
This roller shaft washer is just under an inch in diameter and is used for some of Whirlpool's brands of clothes dryers.Sold individually.
$17.58
In Stock
Mounting Stem/Tub Seal Kit
PartSelect #: PS2351899
Manufacturer #: 6-2095720
This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.
$130.98
On Order
Rubber Injector Valve
PartSelect #: PS11738945
Manufacturer #: WP216201
This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle.
$27.19
In Stock
Common Symptoms of models starting with SE1000
[Viewing 16 of 16]Noisy
Fixed by
these parts
these parts
Show All
Leaking
Fixed by
these parts
these parts
Show All
Burning smell
Fixed by
these parts
these parts
Show All
Will not drain
Fixed by
these parts
these parts
Show All
Will not agitate
Fixed by
these parts
these parts
Show All
Door won’t close
Fixed by
these parts
these parts
Show All
Spins slowly
Fixed by
these parts
these parts
Show All
Marks left on clothes
Fixed by
these parts
these parts
Show All
Too hot
Fixed by
these parts
these parts
Show All
Not Heating
Fixed by
these parts
these parts
Show All
Drum Not Spinning
Fixed by
these parts
these parts
Show All
Will Not Start
Fixed by
these parts
these parts
Show All
Spinning Issues
Fixed by
these parts
these parts
Show All
No hot or cold water
Fixed by
these parts
these parts
Show All
Shaking and Moving
Fixed by
these parts
these parts
Show All
Won’t Start
Fixed by
these parts
these parts
Show All
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
noisy rollers, broken latch
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job.
Thank you.
Thank you.
Parts Used:
-
gerry from west covina,, CA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Wrench (Adjustable), Wrench set
648 of 675 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The blower fan (nylon) stripped off the motor shaft (steel)
Removed the front cover (screws on bottom 0f face)...removed blower cover....spring pliers to remove and install blower fan. the rest of the time was spent cleaning the inside of the shell as well as the vent. Reassembled and dryer runs better than it has for many years.
Parts Used:
-
Stephen from Lafayette, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:1- 2 hours
-
Tools:Nutdriver, Pliers, Screw drivers
565 of 571 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Parts Used:
-
Charles from Whitman, MA
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Screw drivers
568 of 614 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!