This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Ask our experts a question about this model and we'll get back to you as soon as possible!
5 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Lenny
February 24, 2023
It keeps going off balance, even with a small load
For model number MVWB765FW4
Hi Lenny, thank you for asking us. Based on our research, the following parts are most probably causing this issue in your appliance: the leveling leg, part number PS11757131, and the suspension rod kit, part number PS12347544. Also, before any replacement, please ensure that all four legs are in firm contact with a solid floor. If it is so off balance that it shakes, then you can check and replace part number PS12347544. We hope this solves your problem!
What is the problem when it goes off? Balance on the spin cycle?
For model number MVWB765FW4
Hello Lenny, thank you for reaching out. According to our research, you may need to replace the lid lock assembly, part number PS11722981. Good luck with your repair!
My washer no longer chimes or makes any noise when i touch the buttons to start the washer or when i select the wash i want to put it on
For model number MVWB765FW4
Hello Mari, Thank you for writing. We have researched the model you have provided and have found the part you are looking for is the Speaker PartSelect Number PS12114396. Using a flat screwdriver, hold down clips of the top panel assembly. Then unplug the cable from the front panel to the main board. Then, remove all screws that held the control panel to the sheet metal housing and the 2 screws that held the speaker to the control panel. Replaced the speaker and re-assembled. Good luck with your repair.
My kid is broke had a new one out on couple years ago same problem other side. The hinge is cracked and broke and lid will not lock or close
For model number MVWB765FW4
Hello Gail, thank you for reaching out. If the lid is not locking, you will need to replace the lid lock assembly, part number PS11722981, and the wire hinge left side, part number PS11746533, and the wire hinge right side, part number PS11746675. Replace the broken washer lid with part number PS12584356. If you require assistance to place an order, please contact customer service. We hope that helps!
What is the problem when it’s on spin cycle only and becomes unbalanced and shakes violently. That is the only time it shakes like that and stops and goes back to rinse cycle .
For model number MVWB765FW4
Hello Barbara, thank you for contacting us. According to our research, shaking can be caused by a faulty suspension rod, part number PS12347544. You need to check this part to resolve the issue. We hope this solves your problem!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.
