This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This front load washer cleaner removes odor-causing residue. Use it once a month and it will keep your machine fresh and clean. Package comes with 3 tablets.
Ask our experts a question about this model and we'll get back to you as soon as possible!
38 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Ken
March 24, 2020
Washer is dead after displaying codes e2 &f6
Now it is completely dead.
For model number MVWB765FW0
Hello Ken,
Thank you for your question. The E2F6 error code means the control board under part PS11770139 for your model is defective and would need to be replaced. We hope this helps.
What does the f6 and e2 flashing on the panel mean.Washer has quit working and the f6 and e2 flash.
For model number MVWB765FW0
Hello Gary and thanks for writing.
The F6 E2 alert indicates there is an issue with the appliance control unit, user interface or associated wiring. Unplug the washer, wait five minutes, then plug back in. We hope this helps. Please contact us anytime.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Edith
August 16, 2021
The lid disintegrated at the corner where it attaches to the washer. The plastic broke into pieces. I purchased this unit 4/17/2020. I am still under warranty. Have other customers had this problem?
For model number MVWB765FW0
Hi Edith,
Thank you for your question. Where you are still under warranty with your washer, you will need to contact Maytag. We hope this helps! If you have any questions, please let us know.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Vern
February 4, 2020
Does this model have a washer lint trap that i should clean
For model number MVWB765FW0
Hello and thank you for writing.
There is no information for this particular model, however, there are usually 2 places to find the trap if your unit is equipped with one.
How to Find the Laundry Drain Lint Trap
Along the top rim of the washer drum: Slide your fingers around the top of the washing basin, and you may run into a screen, which you can pull out to remove lint.
Inside the center agitator: If you have a top-loading washer, inspect the center agitator.
For your convenience, we have attached the link to our repair video in case you do need to unclog the drain pump. We hope this helps. Good luck with your repair.
https://www.youtube.com/watch?v=YiMaunCHRAU
1 person found this helpful.
Was this helpful?
Thank you for voting!
David
July 22, 2021
Will not rinse and spin everything else ok
For model number MVWB765FW0
Hello David, Thank you for the question. We suggest testing the Lid Lock Assembly. If the Lock is defective it will not allow the tub to spin for safety precautions. We hope this helps!
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.
1.) disconnect power to your washer. Turn off water supply and disconnect from the washer.
open the washer top and remove plastic cap from the wash plate
2.) using 7/16 socket, remove bolt from the wash plate. If you can't remove it with a socket , I recommend using impact wrench.
3.) remove wash plate ( you might need to spray penetrating oil or wd40 inside the bolt hole to loosen it. Check to make sure the wash plate gear grooves are not worn down, if they are, replace it.
4.) using your Maytag specific spaner nut wrench, remove the spaner nut from the shaft of the gear case. This should be right underneath where the wash plate was. If you can't turn it by hand , use a rubber mallet or hammer to encourage it.
5.) some people remove the wash basket at this point. I don't think it is necessary.
6.) close your washing machine. Tape the top closed to keep it from flying open. Tilt your washer back and prop it up where you have access to the underside of the washing machine.
7) remove motor rotor bolt and pull rotor off of the motor.
8.) disconnect the two wire connectors that supply power to motor. using a socket, remove bolts that are keeping motor attached to the gear case.
9.) Now that the gear case is all the is remaining on the underside, you can remove the 4 bolts that are holding the gear case to the washer. Now try to pull gear case out.
10.) if gearcase will not pull out, lower washer back to upright position. Spray penetrating oil or wd40 around the shaft of the gearcase and allow it to sit for 5-10 minutes. Using a hammer, lightly tap on the shaft of the gearcase and it should now fall out. ( you might have to apply penetrating oil again, or apply more force with the hammer.
11.) reinstall motor to new gearcase. Insert new gear case to the washer. Reinstall bolts and reconnect power supply wires.
12. ReInstall spaner nut inside the washer, reinstall wash plate.
Raised lid to remove two Torx head screws from each hinge. Lid will then lift off of hinges. Installation of new lid was the reverse of the removal procedure. It is best to install one hinge to the lid by removing that hinge from the washer. The lid can then be installed by inserting that hinge into it's spot and then over the other hinge. Install the hinge screws into the second hinge and the job is complete. The lid now closes properly allowing the automatic lid lock to function properly.