This an authentic OEM 40-Watt replacement light bulb, used in a number of household appliances. It is specially designed to withstand extreme temperatures, which is why these replacement bulbs are mos...
This hinge is located on each side of the oven door. The hinges control the rate that the oven door opens and closes, and allows the door to stay open at an angle. This hinge can be used on either the...
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Imbi Kovacs
December 15, 2019
How do you lubricate the oven door hinges? Also, how do you remove the oven door?
For model number MEW6630DDS
Hello Imbi, thank you for your question. Oven door hinges can squeak over time. Turn the oven off. Allow it to cool. Grip the oven door handle and pull it open. Apply general purpose grease or high-temperature oil to the pivoting joints of the hinges. Open and close the oven door several times until the squeaking stops. This door can be removed by following the video instructions at this link.
https://www.partselect.com/PS11744215-Whirlpool-WP74008014-Door-Hinge.htm?SourceCode=4&SearchTerm=MEW6630DDS&ModelNum=MEW6630DDS
I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Chris
December 19, 2019
My Maytag wall oven will come on but it shuts itself off after a little bit. Probably around 20 mins or so. It’s just the top oven and the bottom oven works perfectly. I will put cookies in the oven on 350 degrees to cook for the same amount of time that i normally cook them on. They were burnt and overdone after 10 mins.
For model number MEW6630DDS
Hello Chris, thank you for your question. We would recommend testing the oven temperature sensor, Part Number: PS1570174 and if that part is ok, the issue would be with the oven control board. I hope this helps.
Was this helpful?
Thank you for voting!
Dennis
December 14, 2019
Oven light (top) will not turn off.
For model number MEW6630DDS
Hello Dennis and thanks for writing.
It certainly sounds like a faulty door hinges PS11744215 check the part and replace it if needed. We hope this helps. Please contact us anytime.
Removed the oven door by opening slightly, then pic door up to remove. Remove 2 screws holding oven sensor in place, gently pull on sensor to remove, had to remove about 8 inches to get at plastic connector. Unplug connector, had to use an adapter cable supplied with the PartSelect kit to install new sensor, push cable back into opening, reinstall 2 screws. The oven works fine! Note that due to thermal lag the temperature overshoots to 370 degrees and undershoots to 340 degrees, this appears to be normal oven operation. Putting door back in place was easy.
First I removed the two screws that hold the element in place. I then pulled the sensor out about 3 inches and disconnected the two wires. Next, I connected new sensor and screwed the new sensor back in place. One area for caution. Make sure that the electrical connection is pushed in past the insulation on the back side of the oven. Failure to do so will cause the plastic plug connector to melt from oven heat.
Parts arrived in three days and it was an easy swap of the hinges but the same problem still existed: the oven door wouldn't close completely, so the oven light stayed on and the convection wouldn't work either unless the door closed all the way. The replacement hinge's springs apparently aren't strong enough to close it and the springs aren't adjustable - which is a design flaw. I did correct the problem though, by using three dollars worth of 1" round magnets, which I placed inside the door: they stay put and are strong enough to pull the door tight.