This front glide kit comes with a blue plastic glide, a brown cork pad, and two metallic rivets. Two kits are required per appliance. A rivet tool is required for this installation.
This gas dryer ignition coil set comes with two ignition coils: one three-terminal boost/hold coil, and one two terminal secondary coil. Usually only one of them burns out but you should replace them ...
At 91-5/8 inches in length, this dryer drum belt from Maytag has five ridges. It is all black in color and is made entirely of rubber. This flat belt is 3/8 of an inch wide.
This is a rectangle shaped lint filter screen used for some gas and electric clothes dryers. The dimensions of this lint filter screen are approximately twelve and a half inches long by seven and thre...
This timer dial skirt is just over three inches in diameter. It is white in color and is made entirely of plastic. This skirt has a gray indicator triangle.
This flat style igniter comes with a wire harness connector. This part ignites the gas within the dryer. Bracket is NOT included.
$48.90
In Stock
Questions And Answers for MDG4000BWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
3 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Dan
August 11, 2022
Circuit breaker is tripped as soon as I rotate the timer knob in either cw or ccw direction. Dryer will not operate.
For model number MDG4000BWW
Hello Dan, Thank you for the question. This is normally caused by a loose wire connection. We suggest opening up the controls and checking the wiring connections and wires for loose connections or damage. If you need help placing an order, customer service is open 7 days a week. Please feel free to give us a call. We look forward to hearing from you!
Was this helpful?
Thank you for voting!
D
August 29, 2022
Dryer quits heating after 5 mins. Dryer exhaust vent has been replaced and cleaned inside vent in dryer. Could this be that the dryer cycling thermostat has gone bad? Please advise. Thanks
For model number MDG4000BWW
Hello D, Thank you for the question. If the Outlet Duct Assembly and the Cabinet is also cleaned from any lint build up we suggest testing the Dryer Cycling Thermostat and the Cycling Thermostat with a Multimeter. We hope this helps, good luck with this repair!
Trying to decide if we should buy a new dryer after 24 years! Or home repair. The dryer still works but intermittently has a loud squealing noise.
For model number MDG4000BWW
Hi Adrienne, thank you for the great question. We have concluded that the issue is with the drive belt. The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor. Over time, the drive belt can become frayed or otherwise damaged. If the drive belt is frayed or damaged, the dryer will be noisy as it turns. Inspect the drive belt for signs of wear. If the drive belt is worn, replace the drive belt, part number PS11741110. We hope this sorts out your problem!
first, I unplug the power supply of the dryer then I removed the two screws at the bottom of the dryer then pulled out the front part of the dryer,unplugged the blue & yellow wire for the on/off switch for the door,at the back of the dryer I unscrew the pannel for the belt,disconect the belt,and I unscrew the four screws on both side of the front pannel to remove the front cover of the drum. Once I removed the front cover of the drum I can now remove the drum itself to access the drum support roller. I unscrew the rollers then replace it with the new once. It was an easy job. Thank you.