This V-style drive belt is about 51" long and 3/8" wide. This part is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt encounter wear and tear.
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. NOTE: This is a redesigned part. The pump now mounts on to the b...
Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY availab...
This package contains a new set of six springs. The suspension springs in your washer connect to the bottom of tub, and help to hold it in place. If your washer tub shakes, or moves around a lot durin...
This hose clamp extends from half an inch to an inch in diameter. It is made entirely of metal and is intended for use with Maytag brand washing machines.
This water valve is for 60% hot water and 40% cold - This is done to save on energy.
$157.00
In Stock
Questions And Answers for MAV2755AWW
Ask our experts a question about this model and we'll get back to you as soon as possible!
6 questions answered by our experts.
< Prev
1
2
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Randy
December 2, 2019
Washer makes loud noise and looks like the small pulley underneath is bad..it is not the other small drive pulley or the larger pulley.. could this cause the agitator not to work..? its like its froze up and makes a loud squealing noise when trying to turn... belt is in good condition. would need to order pulley but want to make sure its the correct one..
For model number MAV2755AWW
Hello Randy, thank you for writing. Yes, this sounds like a faulty Transmission Pulley and Bearing, part number PS2003651 for your model washer. Good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Nick
December 28, 2023
I get a burning plastic smell after spin cycle.
Do you think it could be the drive belt.
For model number MAV2755AWW
Hello Nick, thank you for your inquiry. Based on our research, the issue could be most probably with the drive belt. We would suggest replacing the drive belt, part number PS11738882, to solve the problem. Glad to be of help!
The cold water setting fills very slowly. I replaced the hot-cold fill valve and it didn't change anything. Any help would b appreciated.
For model number MAV2755AWW
Hi Lyndon, thank you for your question. There could be two other parts that are the issue. You may want to check your water pressure switch: PS2200077, and your pressure switch hose: PS11738826. Check the hose for any holes or breaks, and it if has been clogged. If those two parts are fine then you may want to check how your pressure from your home is to the appliance. You could also check your funnel, the part that actually funnels the water into your tub: PS11738827. Just check to see if that is blocked or stopping the water flow at all. Good luck with your repair.
Was this helpful?
Thank you for voting!
Anne
December 5, 2022
Machine squeals loudly only when spinning. We are thinking of changing the drive belt. Do you have an install tool that is compatible with this model?
Thanks!
For model number MAV2755AWW
Hi Anne, thank you for reaching out. Before replacing the drive belt, part number PS11738882, we would recommend checking the following parts to fix the issue: Drain Pump, part number PS11741803, and Snubber Ring, part number PS11738845. We hope this helps! If you need help placing an order, customer service is open 7 days a week. Thanks again for your great question.
Hello Tom, thank you for contacting us. The most common cause of a washer making a loud grinding noise during the agitation cycle is a worn-out bearing or broken pulley. We would recommend checking the transmission pulley and bearing kit, part number PS2003651. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated.
The pump is located behind a small panel on the back, lower left side of my washer. It's attached to the bottom frame with 3 screws. It has two hoses attached, each with one spring clamp. Lift one side of the washer and slip the drive belt off the pully. Release the spring clamps on the hoses with a pair of pliers and remove the hoses. A small amount of water will drain from the hoses and pump when removed. Remove the three screws holding the pump to the frame and remove the pump. Install the new pump in the same position. Reattach the hoses, replace the belt, and reinstall the cover panel. That's all there is to it.
unplug the washer. Removed the top of the washer by removing the hold scews and tabs on the upper back. Place a scew drive under the front and pry up to release the snap tabs. Then the front panel by removing the two screws on top and lift the panel up to expose the motor at bottom front. Remove the motor cover (plastic)and motor from the base, replace the pulley on the shaft (you may need to break or pry the old pulley off) install the new pulley making sure it is all the way up the shaft locking the tabs into the shat groove. Reinstallmotor to the base. To replace the belt, tilted the unit backwards to access the pulleys from the bottom and installed. Note: it ios easier to install the belt fully on the two smaller puleys attcahed to the drive motor and pump and then wrap as much as you can around the larger drum pulley. Hold the belt in one hand and turn the drum pulley clockwise with the other and the belt will follow and install. reverse steps to reassemble.