Sold individually. This surface burner grate is for ranges.
Surface burner grate provides a stable surface for cookware on the surface burner.
Wait until the surface is cool to the touch before ...
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
This oven rack is chrome in color and is approximately 24.76 inches wide by 15.78 inches deep. If your old oven rack is damaged, you should consider replacing it. Many of our customers have determined...
This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch...
This part is the replacement door gasket for your oven. It is made of gray rubber and is sold individually. The door gasket runs along the circumference of the oven door and creates a seal that insula...
Ask our experts a question about this model and we'll get back to you as soon as possible!
4 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Colleen
December 16, 2021
I broke the outer glass on the oven door. I have been told it is not longer available. Is there another replacement part for this?
For model number KGSS907SSS02
Hello Colleen, thank you for writing. No, there are no replacement parts. All three options, Stainless, Black and White have been discontinued. Good luck and have a great day.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Leon
March 8, 2020
Can l purchase a complete door ?
For model number KGSS907SSS02
Hi Leon,
Thank you for your question. We do not sell a complete door for this model, only the individual parts for it. If there is a part on the door that is damaged that you need to replace, please let us know what it is and we would happy to verify if we have it available for you. We hope this helps. Thank you and have a great day.
Was this helpful?
Thank you for voting!
Jennifer
August 15, 2023
My panel is reading: Lost Communications - error code F6 E0
Do you have any idea what this could be? A burnt out fuse perhaps??
For model number KGSS907SSS02
Hi Jennifer, thank you for reaching out. The error code F6E0 indicates there is a communication error between the main control board and the interface control board. To solve this issue, you may need to check the wiring between the two boards, if that is not causing the issue then you may need to replace the control board, part number PS11747371. We hope this helps!
My left-side front burner won't ignite. If I manually place a fire source near it, it will which tells me that there is access to a gas source. I have taken it completely apart down to the center nut where the gas comes in and cleaned it. It still does not work. Do you think it is the surface ignitor that needs to be replaced?
For model number KGSS907SSS02
Hi Joni, thank you for the question. Based on the description, the issue is with the surface burner igniter, part number PS11748327. You may need to replace the ignitor to fix the issue. We hope this solves your problem!
Something Kitchen Aid wont tell you but running a self clean on this model stove blows the fuse located on the back of the stove.
First I slid the stove out and removed the back of the stove held in place by 8 Phillips screws. The thermostat fuse is located near the top middle on the back of the stove. Remove the 2 screws holding it in place. Disconnect the wires, plug in the new part. Put it all back together. Job done in less than 30 minutes.
This repair would have cost $164 through A&E factory service.
My wife used the self cleaning function for the first time after 1.5 years of owning, of course out of warranty. A quick google search identified the problem. Called Kitchenaid, they said of course it can't be that simple, they had never heard of this problem, need to schedule a service call. Googled and found this site, Ordered the part, came in, only took a screwdriver and about 20 minutes, just like all the other posts.
shame on Kitchenaid for not owning up to the problem. I even e-mailed them all the links, they did not acknowledge them.
This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.