This handle may appear white, but is light gray in color called Platinum. This door handle for your washer is sold without screws, they can be ordered separately, or you can reuse the existing screws ...
This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.
This 18 ml bottle of white appliance touch-up paint is used to cover scratches or marks on your appliance. The white touch-up paint can be used on refrigerators, microwaves, ranges, clothes dryers, an...
Sold individually. These shock absorbers keep the washer from vigorous shaking during its cycles. This shock absorber is for washers.
Shock absorber absorbs the vibrations and movements of the oute...
This water inlet valve attaches the water lines to the back of your appliance. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.
This drive belt is made to slip on the motor pulley to bring the basket up to the speed required and this makes the belt get wear and tear.
NOTE: Per Manufacture, belt measures 48.22" long uninstall...
Used to help hold your bellow in place on your washer.
$47.23
In Stock
Questions And Answers for GHW9150PW4
Ask our experts a question about this model and we'll get back to you as soon as possible!
12 questions answered by our experts.
< Prev
1
2
3
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Yolanda
December 12, 2019
I need a spider for this model
For model number GHW9150PW4
Hello Yolanda, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Manufacturer Part Number WPW10250573 and only sold as part of the basket. I looked up the part and it is listed as No Longer Available/Discontinued sorry. There are no part substitutions listed. My suggestion here would be to call the manufacturer and see if they can provide you with a substitution for these part numbers. We hope this helps!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Theresa
January 30, 2020
I am looking for the door handle for the above model. Thank you.
For model number GHW9150PW4
Hello, Thank you for contacting us. I have researched the model you have provided and have found the part you’re looking for is Door Handle (Part# PS11744938).
When i turn on the washing machine and push start and nothing happen , what is the problem , can you tell me , is it the circuit board ? Or the door switch ?
For model number GHW9150PW4
Hello William,
Thank you for your question. Our sources suggest that its likely the door lock latch under part PS11745016 for your model that would need to be replaced to fix the issues with your washer. We hope this helps.
After cycle starts it flashes f05. I replaced temperature sensor still continues flashing f05 after I unplugged it for one minute and plugged back in error code still keeps coming up
For model number GHW9150PW4
Hello Carl, Thank you for the question. Error code F05 indicates a Water Temperature Sensor Error. During the water filling in the wash cycle, if the temperature sensor is out of range the F05 error code will be displayed. If the Sensor is good, we suggest you check the water source to make sure hot water is on and the correct temperature and pressure. We hope this helps.
Was this helpful?
Thank you for voting!
Victor
March 17, 2023
I am getting a F02 code on my whirlpool front end loading washer . It was also failing to spin or let water in .
It was recommended on your site that it could be a bad drain pump , a clogged , or a pinched drain line . I replaced the drain pump , and checked the drain line .
The washing cycle now starts but it is still giving me an F02 code , and at the end of the cycle the clothes are still pretty wet ( as though all of the water was not drained out . Is there anything else besides that drain pump that could be a problem and also give me the F 02 code ..
the drain hose seems to be good .
Would a diagnostic check tell you anything , and if so what are the steps you need to take to preform that ?
Thank you .
For model number GHW9150PW4
Hello Victor, thank you for getting in touch. The error code F02 is usually caused by a kinked drain hose, a clogged drain hose, or not using high-efficiency detergent. If you have already checked the drain pump and drain line, you need to make sure you are using high-efficiency detergent. Using non-HE detergent or more than the manufacturer's recommended amount of detergent can cause excessive suds. The excess suds will slow or stop the removal of water from the washer. We hope this is what you were looking for!
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
The first step is to remove the retainer ring that holds the outside of the bellow in place. To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up. You will find a spring streached about 3" connected to a small diameter wire (1mm.) that runs all the way around the outside portion of the bellow. Use a small screwdriver or other to pull and pry the spring away from the rubber bellow. Be careful not to damage the spring or ring. Once you have grip on it, pull it carefully toward you then up and off of the bellow.
The front portion of the bellow is now free and can be peeled off. Start at any point and pull the rubber bellow in toward the opening of the washer, it comes off easily. When you get to the detergent outlet on the upper left side, grab the plastic tube and carefully pull the bellow from around it. There is no adhesive or clamp holding this in place, just friction. Remove the rest of the front portion of the bellow. Push as much of the bellow into the washer as possible to get it out of the way.
Once this is off comes the slightly tricky part. Look up at the top right portion of the bellow that is still attached. You may need to feel with your hand but you should be able to see it. You are looking for the screw/nut end of a giant hose clamp. This hose clamp goes around the entire bellow and the secures it to the portion that holds the basket. This is where the stubby screw driver comes in handy. There is not nearly enough room for a standard one and a nut driver or wratchet are too big. The nut will be pointing down and will need to be replaced the same way. Loosen the hose clamp almost all of the way, not necessary to have the hose clamp come completely apart. You can now remove the entire hose clamp from around the bellow by pulling it forward. You will need to remove the hose clamp from the washer. To do this, squeeze it in from the sides about 6", don't kink it. Push it down toward the floor between the basket and the metal front panel. You will now be able to remove it from the top of the opening and be able to pull the bottom portion out. Pull the old bellow completely out, very easy to do.
Time to install the new bellow. Figure out which side goes in and which faces out. The big hint is that the water inlet is on the upper left side. You will notice at the top of the bellow on the portion that goes inside of the washer, you will find a small triangular shaped tab about 1/4" high. This is your centering mark. This will be at the very top. If you keep this at the top, everything will line up perfectly.
Slip the bellow over the edge of the portion that holds the basket where you removed the old one. I started at the top and worked left so I could install the detergent inlet tube. Pull this through the bellow carefully. It doesn't take a lot of force. As you are pressing the bellow on this lip, you will notice that there is a 1/2" high back stop all of the way around. This is great because as you press it on, there is a positive stop and you can't go further than necessary. Continue to press it in all of the way around.
Now it is time to install the Hose clamp. Un bend anything that might have bent on the clamp. With the nut at the top or top right with the nut facing down to the floor while holding it vertically, squish it slightly inward, put the bottom portion in first then the top portion. Orient is as it was when you took it off. Slide it around the bellow. You will feel a positive stop. Grab the stubby screwdriver and tighten down the hose clamp. I did about a medium force when tightening. It doesn't take a lot of force.
Now it is time to pull the remaining part of the bellow out of the basket and fit it into place. Press it around the outside portion of the opening so it hooks over the lip. This w
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door. (3) I packed towels under the washer. (4) I slowly removed the cleanout in the front of the pump, using the water vac to catch the water as it leaked out. (5) I removed the wiring to the motor. (6) I removed the screw that holds the pump in place with a Torx T-20 socket. (7) I pulled the pump forward so the clamps that hold the drain hose and discharge hose could be removed using the hose clamp pliers. ( they come off much easier then they go back on ). (8) I tested the pump and found it would run but was making a lot of noise and running slow. (9) To reinstall start with number (7) and work backwards to number (1) skipping (3) and (4). Don Kramer Wichita, Kansas