This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoid on the valve open and close according to the desired amount of water needed.
The circulation pump adapter, or pump adapter assembly connects the circulation pump to the tub of your dishwasher. If your dishwasher is leaking around this adapter, check the connection to ensure ev...
The hinge link on your dishwasher connects the spring to the dishwasher door hinge. If the hinge link becomes cracked or damaged, you may not be able to shut or lock your dishwasher door properly. In ...
This is the replacement fine filter hub nut for your dishwasher. It is made of white plastic and is approximately 3 inches in diameter. The fine filter hub nut is also known as the lower spray arm hub...
This kit includes the drain hose with black rubber end fittings and a clamp.
$69.30
Special Order
Questions And Answers for GHDT168V00SS
Ask our experts a question about this model and we'll get back to you as soon as possible!
2 questions answered by our experts.
< Prev
1
Next >
Sort by:
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Sam
January 7, 2022
How to remove the large screen in the bottom under the bottom spinner wand
How to install the gasket around the sump area
Best technique to remove the sump in the back of washer
For model number GHDT168V00SS
Hi Sam,
Thank you for your question. The filter no longer requires or includes a gasket, but may require a silicone or sealant when installed. When doing this repair, please make sure to disconnect the power from your appliance before starting. 1. Remove the lower dishrack from the appliance by rolling it all the way out. 2. To remove the lower wash arm, lift up on the arm and turn it counter clockwise. This should disconnect the arm from the base. 3. To remove the nut you will turn it counter clockwise to release it. 4. Remove the accumulator/filter by lifting it up out of place. 5. You will then have to disconnect the water tube. There is a little tab at the rim where it connects with the base. Just push that down with the help of a flat head screw driver and that should release the tube from the base. Turn the tube and base toward the left to separate them from each other. 6. Now we are going to take the sump cover off just by squeezing it and lifting it out of place. 7. To remove the sump filter you will need a putty knife and your flat head screwdriver. This part is a little difficult as there are locking tabs on each side of the sump filter and you have to use both your putty knife and screw driver to release them both at the same time. The easiest way to try and do this is by sticking your putty knife through the gap at the top of the sump filter between the filter and the course filter. Push it down until it touches the bottom of the dishwasher. Then, lifting the course filter from the front, use your screw driver to reach in and depress the locking tabs on the other side of the sump filter. 8. Once you have the sump filter out, then remove the rest of the base by unscrewing it counter clockwise. Then you should simply be able to lift out your course filter and change it out for the new one. Follow these steps backwards to reinstall your parts. We hope that helps. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Samuel
December 9, 2022
No display unit will not reset. Worker on 12/2 but not 12/4. What to check?
For model number GHDT168V00SS
Hello Samuel, thank you for contacting us. We would recommend checking the control board, part number PS4704219. Check all the terminals of the board with a multimeter to find the fault. Customer service is available 7 days a week if you require assistance placing an order. Thanks again for reaching out!
All I had to do is take out the rack, pop off the old wheels, place the new stud rollers on, then pop on the new wheels. So easy and now my dishes don't get chipped when I pull the rack out and push it back in. I wish I didn't wait so long to order new parts.
Pull old rack out, slip new one in! One thing i did was order wheels and studs as i was unaware they lower rack came fully equiped with all wheels,studs, and flip up dish dividers. So if your replacing the rack no need to order the wheels! The diagram made it look as if you only et the wire rack and not all the added pieces.
